Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

TIRE PRESSURE WARNING SYSTEM > TEST MODE PROCEDURE

for Preparation Click here



ENTER TEST MODE
  1. Turn the power switch off.

  2. Connect the Techstream to DLC3.

  3. Turn the power switch on (IG).

  4. Check that the tire pressure warning light comes on for 3 seconds and then goes off.

  5. Turn the Techstream on.

  6. Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.



  7. F100632E09
  8. Confirm that the tire pressure warning light in the combination meter blinks at 0.125-second intervals.


PERFORM SIGNAL CHECK

HINT:
  1. When entering signal check mode, the tire pressure warning ECU sets all the signal check DTCs first.
    After completing signal check for each inspection item, the DTCs for systems that are determined to be normal by the tire pressure warning ECU will be erased.
    The DTCs for other inspection items may not be erased when only a certain signal is inspected.
  2. When signal check returns to normal mode, all the signal check DTCs will be erased.

  1. Turn the power switch off.

  2. Connect the Techstream to DLC3.

  3. Turn the power switch on (IG) and turn the Techstream on.

  4. Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.

    HINT:
    Every time the test mode DTC clearing conditions are satisfied, the tire pressure warning light comes on for 1 second. Then, the tire pressure warning light blinks at 0.125-second intervals.

  5. Drive the vehicle at 12 mph (20 km/h) or more for 3 seconds or more to check the vehicle speed signal (C2191/91).

  6. Loosen the valve core and rapidly reduce the pressure (at least 40 kPa (0.41 kg/cm2, 5.8 psi) within 30 seconds or more) to check the transmitter data (C2181/81 to C2185/85).

    HINT:
    The transmitter ID can be transmitted by rapidly reducing the tire pressure.

  7. Check that the tire pressure warning system test mode DTCs are erased.

    Test Mode DTC
    Test Signal
    Test Mode DTC Clearing Condition
    C2181/81 to C2185/85
    Transmitter Data
    Data is received from the transmitter which has a registered ID in the tire pressure warning ECU
    C2191/91
    Vehicle Speed Signal
    Vehicle speed of 12 mph (20 km/h) or more is detected for 3 seconds or more

  8. Result

    HINT:
    After the signal check is completed, check for a test mode DTC to confirm the system status.


    Condition
    Procedure
    Test mode DTC is output
    Repair the faulty part and enter SIGNAL CHECK again
    Test mode DTCs are cleared
    No problem

  9. End of SIGNAL CHECK

    1. After completing the test mode (SIGNAL CHECK), turn the power switch off and disconnect the Techstream.

  10. DTC of SIGNAL CHECK (TEST DIAGNOSIS)

    1. If a trouble code is displayed during the test mode DTC check, check the circuit listed for that code. For details of each code, refer to the "See page" below.

      DTC No.
      Detection Item
      Trouble Area
      See page
      C2181/81
      Transmitter ID1 not received
      1. Tire pressure warning valve and transmitter
      2. Tire pressure warning antenna and receiver
      3. Harness or connector
      4. Tire pressure warning ECU
      Click here
      C2182/82
      Transmitter ID2 not received
      C2183/83
      Transmitter ID3 not received
      C2184/84
      Transmitter ID4 not received
      C2185/85
      Transmitter ID5 not received
      C2191/91
      Vehicle speed signal error
      1. Combination meter assembly
      2. Vehicle speed sensor
      3. Harness or connector
      4. Tire pressure warning ECU
      Click here