Home › BODY › ENGINE HOOD / DOOR › FUEL LID OPENER SYSTEM

FUEL LID OPENER SYSTEM > Fuel Lid Opener does not Operate

for Preparation Click here


DESCRIPTION

  1. When the fuel lid opener switch is pushed, a fuel lid opener switch signal is sent to the hybrid vehicle control ECU. The hybrid vehicle control ECU sends a fuel lid open output request signal to the fuel lid opening lid lock, and operates the fuel lid opener motor.
    When the fuel lid opener not operate, one of the following may be malfunctioning: 1) SFI system, 2) FUEL OPN fuse, 3) fuel lid opener switch, 4) fuel lid opener motor, 5) wire harness or connector, or 6) hybrid vehicle control ECU.
    If the fuel tank pressure sensor or fuel vapor containment valve is malfunctioning, the hybrid vehicle control ECU stores the DTC and the fuel lid opener motor will not operate.

WIRING DIAGRAM


B178873E03


INSPECTION PROCEDURE

NOTICE:
If the hybrid vehicle control ECU is replaced, register the ECU communication ID (Click here).

1.CHECK DTC OUTPUT (SFI SYSTEM)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menu items: Powertrain / Engine and ECT / Trouble Codes.

  1. Check the DTC(s) and freeze frame data, and write them down.

  1. Check the details of the DTC(s).
    Result: 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



A
GO TO SFI SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) (Click here)
B


2.INSPECT FUSE (FUEL OPN)
  1. Remove the FUEL OPN fuse from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    FUEL OPN fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE (FUEL OPN)
OK


3.READ VALUE USING TECHSTREAM (FUEL LID OPENER SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

  1. Read the Data List according to the display on the Techstream.

    Engine and ECT (Hybrid Vehicle Control ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Lid Switch
    Fuel lid opener switch status: ON or OFF
    ON: Fuel lid opener switch is pushed
    OFF: Fuel lid opener switch is not pushed
    -

    OK:
    On the Techstream screen, the item changes between ON and OFF according to the chart above.



NG
Go to step 8
OK


4.PERFORM ACTIVE TEST USING TECHSTREAM (FUEL LID OPENER MOTOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. Perform the Active Test according to the display on the Techstream.

    Engine and ECT (Hybrid Vehicle Control ECU): 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Fuel Filler Opener
    Operate fuel lid opener motor
    ON / OFF
    Confirm that engine is stopped

    OK:
    Fuel lid is opened by Active Test.



NG
Go to step 5
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

5.INSPECT FUEL LID OPENER MOTOR ASSEMBLY
  1. Remove the fuel lid opener motor (Click here).



    B178862E01
  1. Apply battery voltage to the lock control and check the motor operates in the open direction.

    Standard:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 2
    Battery positive (-) → Terminal 1
    Motor operates and shaft moves in open direction

  1. Check the shaft stroke.

    Standard:
    10.3 mm (0.406 in.) or more.



NG
REPLACE FUEL LID OPENER MOTOR ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FUEL LID OPENER MOTOR - HYBRID VEHICLE CONTROL ECU)


    B178866E01
  1. Disconnect the fuel lid opener motor connector.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D36-11 (FUO) - O41-1
    Always
    Below 1 Ω
    D36-11 (FUO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (FUEL LID OPENER MOTOR - BATTERY)


    B178867E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O41-2 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

8.INSPECT FUEL LID OPENER SWITCH


    B178863E01
  1. Remove the fuel lid opener switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (B) - 4 (E)
    Fuel lid opener switch is pressed
    Below 1 Ω
    3 (B) - 4 (E)
    Fuel lid opener switch is not pressed
    10 kΩ or higher



NG
REPLACE FUEL LID OPENER SWITCH (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (FUEL LID OPENER SWITCH - HYBRID VEHICLE CONTROL ECU)


    B178868E01
  1. Disconnect the hybrid vehicle control ECU connector.

  1. Disconnect the fuel lid opener switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D35-15 (FUEL) - D61-3 (B)
    Always
    Below 1 Ω
    D35-15 (FUEL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK HARNESS AND CONNECTOR (FUEL LID OPENER SWITCH - BODY GROUND)


    B178869E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D61-4 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)