Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A1B-788    Drive Motor "A" Control Module

for Preparation Click here


DESCRIPTION

If the MG ECU is reset due to an auxiliary battery voltage drop or abnormality, the hybrid vehicle control ECU will set this DTC.

HINT:
The term "drive motor A" indicates MG2.


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A1B
788
Error in reset signal from the power source IC
  1. Auxiliary battery
  2. Wire harness or connector
  3. Inverter with converter assembly (MG ECU)

MONITOR DESCRIPTION

When detecting an abnormal reset of the CPU caused by the power supply IC in the MG ECU, the hybrid vehicle control ECU will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0A1B (INF 788): Reset from power IC
Required sensors / components
Motor Generator control ECU (MG ECU)
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the DTCs listed are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


Motor Generator control ECU (MG ECU)
Internal error

COMPONENT OPERATING RANGE


Motor Generator control ECU (MG ECU)
DTC P0A1B (INF 788) is not detected

WIRING DIAGRAM


A179953E01


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals. After waiting for 5 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:
Waiting for at least 5 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

1.CHECK CONNECTOR CONNECTION CONDITION (MG ECU CONNECTOR)

CAUTION:
Be sure to wear insulated gloves.

  1. Turn the power switch off.



    A170989E01
  1. Remove the service plug grip (Click here).

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the inverter cover (Click here).

    NOTICE:
    1. Wrap the round interlock terminal for the inverter cover with insulating tape to prevent it from shorting to ground.
    2. Prevent coolant in the inverter reserve tank from entering the inverter.
    3. Removing the inverter cover causes the MG ECU board to be exposed. Therefore, temporarily install the inverter cover for each area to be inspected.

  1. Check the connections of the MG ECU connectors.

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


2.CHECK HARNESS AND CONNECTOR (IGCT RELAY - MG ECU)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

  1. Remove the IGCT relay from the engine room relay block.

  1. Disconnect connector A42 from the MG ECU.



    A201274E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    A42-7 (+B) - IGCT relay terminal 5
    Power switch off
    Below 1 Ω
    A42-4 (+B2) - IGCT relay terminal 5
    Power switch off
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    A42-7 (+B) or A42-4 (+B2) - Body ground and other terminals
    Power switch off
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT MG ECU (+B VOLTAGE)

CAUTION:
Be sure to wear insulated gloves.



    A174223E05
  1. Check that the service plug grip is not installed.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A42-7 (+B) - Body ground
    Power switch on (IG)
    10 V or more
    A42-4 (+B2) - Body ground
    Power switch on (IG)
    10 V or more

    NOTICE:
    Turning the power switch on (IG) with the service plug and inverter cover removed causes interlock switch system DTCs to be stored. Clear the DTCs after performing the inspection.



NG
CHECK AND REPLACE BATTERY
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)