Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch

for Preparation Click here


DESCRIPTION

  1. When the AUTO UP/DOWN does not function, the power window control system may be in fail-safe mode. If the system has not been initialized after replacement of the driver door power window regulator motor, it also results in the same problem.

    NOTICE:
    1. The power window control system uses a multiplex communication system (LIN). Inspect the communication function by following HOW TO PROCEED WITH TROUBLESHOOTING. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
    2. When the power window regulator motor assembly (on the driver side) is reinstalled or replaced, the power window control system must be initialized.
    3. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the AUTO UP function is used. In such cases, the AUTO UP function can be resumed by repeating the following operation at least 5 times:
      1. Close the power window by fully pulling up the power window switch and holding it in the AUTO UP position.
      2. Open the power window by fully pushing down the switch.

    HINT:
    If the pulse sensor built into the power window regulator motor assembly (on the driver side) malfunctions, the power window control system enters fail-safe mode. The remote UP/DOWN and AUTO UP/DOWN functions cannot be operated during fail-safe mode. (However, the power window can be closed by holding the power window switch at the AUTO UP position, and opened manually by pushing down the switch.)


WIRING DIAGRAM


B172585E01


INSPECTION PROCEDURE

1.CHECK DTC OUTPUT
  1. Check for DTCs.

  1. Connect the Techstream to the DLC3.

  1. By following the tester screen display, check whether any DTCs are output.
    Result 
    Result
    Proceed to
    No output
    A
    DTC output
    B



B
PROCEED TO INSPECTION PROCEDURE RELEVANT TO OUTPUT DTC
A


2.READ VALUE ON TECHSTREAM (D-DOOR MOTOR)
  1. Use the Data List to check the function of the power window master switch.

    1. Connect the Techstream to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the Techstream on.

    4. Enter the following menus: Body / D-Door Motor / Data List.

    5. Read the Data List according to the display on the Techstream.

      D-Door Motor 
      Item
      Measurement Item / Display (Range)
      Normal Condition
      Diagnostic Note
      D P/W Auto Switch
      Driver side power window AUTO switch signal /
      ON or OFF
      ON: Driver side power window AUTO switch operates
      OFF: Driver side power window AUTO switch does not operate
      -
      D P/W Up Switch
      Driver side power window UP switch signal /
      ON or OFF
      ON: Driver side power window UP switch operates
      OFF: Driver side power window UP switch does not operate
      -
      D P/W Down Switch
      Driver side power window DOWN switch signal /
      ON or OFF
      ON: Driver side power window DOWN switch operates
      OFF: Driver side power window DOWN switch does not operate
      -

      OK:
      ON (switch operates) is displayed on the Techstream.



NG
Go to step 3
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side) (Click here)  

3.INSPECT POWER WINDOW MASTER SWITCH


    B164359E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    8 (U) - 1 (E) - 4 (A)
    Auto UP
    Below 1 Ω
    4 (A) - 5 (D) - 1 (E)
    Auto Down
    Below 1 Ω



NG
REPLACE POWER WINDOW MASTER SWITCH (Click here)
OK


4.INSPECT FUSE (DOOR NO. 2)
  1. Remove the DOOR NO. 2 fuse from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    DOOR NO. 2
    Always
    Below 1 Ω



NG
REPLACE FUSE (DOOR NO. 2)
OK


5.CHECK WIRE HARNESS (MASTER SWITCH - REGULATOR MOTOR)


    B175976E08
  1. Disconnect the M1 and H1 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    M1-4 (A) - H1-4 (AUTO)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side) (Click here)