Home › HYBRID SYSTEM ยท P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A60-288    Drive Motor "A" Phase V Current

DTC    P0A60-289    Drive Motor "A" Phase V Current

DTC    P0A60-290    Drive Motor "A" Phase V Current

DTC    P0A60-292    Drive Motor "A" Phase V Current

DTC    P0A60-294    Drive Motor "A" Phase V Current

DTC    P0A60-501    Drive Motor "A" Phase V Current

DTC    P0A63-296    Drive Motor "A" Phase W Current

DTC    P0A63-297    Drive Motor "A" Phase W Current

DTC    P0A63-298    Drive Motor "A" Phase W Current

DTC    P0A63-300    Drive Motor "A" Phase W Current

DTC    P0A63-302    Drive Motor "A" Phase W Current

DTC    P0A63-502    Drive Motor "A" Phase W Current

for Preparation Click here


DESCRIPTION

The MG ECU monitors the inverter current sensor. These DTCs are for malfunctions in the sensor lines and not for malfunctions in the high-voltage lines.

HINT:
The term "drive motor A" indicates MG2."


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A60
288
Malfunction in the motor inverter current sensor (phase V sub sensor)
  1. Inverter with converter assembly
289
Open in the motor inverter current sensor (phase V sub sensor) circuit
290
Malfunction in the motor inverter current sensor (phase V main sensor)
292
Open in the motor inverter current sensor (phase V main sensor) circuit
294
Performance problem of the motor inverter current sensor phase V
501
Malfunction in the motor inverter current sensor (phase V main and sub sensors offset)
P0A63
296
Malfunction in the motor inverter current sensor (phase W sub sensor)
297
Open in the motor inverter current sensor (phase W sub sensor) circuit
298
Malfunction in the motor inverter current sensor (phase W main sensor)
300
Open in the motor inverter current sensor (phase W main sensor) circuit
302
Performance problem of the motor inverter current sensor phase W
502
Malfunction in the motor inverter current sensor (phase W main and sub sensors offset)

MONITOR DESCRIPTION

The MG ECU monitors the motor inverter current sensor. If the hybrid vehicle control ECU detects a fault, it will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0A60 (INF 288): Motor inverter current sensor / Phase V, sub sensor / Out of range
P0A60 (INF 289): Motor inverter current sensor / Phase V, sub sensor / Open circuit
P0A60 (INF 290): Motor inverter current sensor / Phase V, main sensor / Out of range
P0A60 (INF 292): Motor inverter current sensor / Phase V, main sensor / Open circuit
P0A60 (INF 294): Motor inverter current sensor / Phase V deviation / Short to GND
P0A60 (INF 501): Motor inverter current sensor / Offset malfunction
P0A63 (INF 296): Motor inverter current sensor / Phase W, sub sensor / Out of range
P0A63 (INF 297): Motor inverter current sensor / Phase W, sub sensor / Open circuit
P0A63 (INF 298): Motor inverter current sensor / Phase W, main sensor / Out of range
P0A63 (INF 300): Motor inverter current sensor / Phase W, main sensor / Open circuit
P0A63 (INF 302): Motor inverter current sensor / Phase W deviation / Short to GND
P0A63 (INF 502): Motor inverter current sensor / Offset malfunction
Required sensors / components
Motor inverter current sensor, motor resolver
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the DTCs listed are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


TMC's intellectual property
-

COMPONENT OPERATING RANGE


P0A60 (INF 288/289/290/292/294/501) 
Motor inverter current sensor
DTC P0A60 (INF 288/289/290/292/294/501) is not detected

P0A63 (INF 296/297/298/300/302/502) 
Motor inverter current sensor
DTC P0A63 (INF 296/297/298/300/302/502) is not detected

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals. After waiting for 5 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:
Waiting for at least 5 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

1.CHECK CONNECTOR CONNECTION CONDITION (MG ECU CONNECTOR)

CAUTION:
Be sure to wear insulated gloves.

  1. Turn the power switch off.

  1. Remove the service plug grip (Click here).

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the inverter cover (Click here).

    NOTICE:
    1. Wrap the round interlock terminal for the inverter cover with insulating tape to prevent it from shorting to ground.
    2. Be sure to prevent coolant in the inverter reserve tank from entering the inverter.
    3. Removing the inverter cover causes the MG ECU board to be exposed. Therefore, temporarily install the inverter cover for each area to be inspected.



    A170989E01
  1. Check the connections of the MG ECU connectors.

    OK:
    The connectors are connected securely and there are no contact problems.

    HINT:
    If any DTCs indicating malfunctions in the current sensor circuit are output, overcurrent to the electric vehicle fuse is suspected. In this case, be sure to replace the electric, vehicle fuse after troubleshooting and repairing all output DTCs.



NG
CONNECT SECURELY
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)