Home › HYBRID SYSTEM ยท P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A79-697    Drive Motor "B" Inverter Performance

DTC    P0A79-698    Drive Motor "B" Inverter Performance

for Preparation Click here


DESCRIPTION

Refer to the description of the inverter .
If the inverter receives a rear motor gate shutdown signal from the MG ECU, it will turn all power transistors off which are activating MGR to forcibly stop MGR operation.
The MG ECU monitors the rear motor gate shutdown signal line and detects a malfunction.

HINT:
The term "drive motor B" indicates MGR.


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A79
697
Short to GND in rear motor gate shutdown (RSDN) signal line
Inverter with converter assembly
698
Open or short to +B in rear motor gate shutdown (RSDN) signal line

MONITOR DESCRIPTION

The MG ECU monitors the rear motor gate shutdown (RSDN) signal line. If the MG ECU detects an open or short in the RSDN signal circuit, the hybrid vehicle control ECU will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0A79 (INF 697): Rear motor inverter / Rear motor gate shutdown signal malfunction (short to GND)
P0A79 (INF 698): Rear motor inverter / Rear motor gate shutdown signal malfunction (short to +B or open circuit)
Required sensors / components
Rear motor inverter
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
1 driving cycle
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the DTCs listed are not present
TMC's intellectual property
Other conditions belong to TMC's intellectual property
-

TYPICAL MALFUNCTION THRESHOLDS


Rear motor gate shutdown signal circuit
Open or short

COMPONENT OPERATING RANGE


Rear motor inverter
DTC P0A79 (INF 697/698) is not detected

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals. After waiting for 5 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:
Waiting for at least 5 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

1.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0A79-697 or P0A79-698 only is output.
    A
    Any of the following DTCs are also output.
    B


    DTC No.
    Relevant Diagnosis
    P3232-749
    Open or Short to B+ Blocking of HV Gate Connection
    P3233-750
    Short to B+ in Blocking of HV Gate Connection



B
GO TO DTC CHART (Click here)
A


2.CHECK CONNECTOR CONNECTION CONDITION (MG ECU CONNECTOR)

CAUTION:
Be sure to wear insulated gloves.

  1. Turn the power switch off.

  1. Remove the service plug grip (Click here).

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the inverter cover (Click here).

    NOTICE:
    1. Wrap the round interlock terminal for the inverter cover with insulating tape to prevent it from shorting to ground.
    2. Be sure to prevent coolant in the inverter reserve tank from entering the inverter.
    3. Removing the inverter cover causes the MG ECU board to be exposed. Therefore, temporarily install the inverter cover for each area to be inspected.



    A170989E01
  1. Check the connections of the MG ECU connectors.

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)