Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A94-547    DC / DC Converter Performance

DTC    P0A94-548    DC / DC Converter Performance

for Preparation Click here


DESCRIPTION

Refer to the description of the boost converter .
If the boost converter detects a circuit malfunction or overvoltage, it will transmit this information to the OVL terminal of the MG ECU via the boost converter overvoltage signal line.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A94
547
Boost converter overvoltage signal detection (overvoltage by MG ECU malfunction)
  1. HV relay assembly
  2. Inverter with converter assembly (MG ECU)
548
Boost converter overvoltage signal detection (overvoltage by inverter malfunction)

MONITOR DESCRIPTION

If the boost converter (inverter with converter assembly) detects an overvoltage, it will transmit a boost converter overvoltage signal to the MG ECU. The MG ECU will send information about the malfunction to the hybrid vehicle control ECU. Upon receiving this information, the hybrid vehicle control ECU will illuminate the MIL and set a DTC.

MONITOR STRATEGY


Related DTCs
P0A94 (INF 547/548): OVL detection overvoltage
Required sensors / components
Boost converter
Frequency of operation
Continuous
Duration
TMC's intellectual property
MIL operation
Immediately
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the DTCs listed are not present
TMC's intellectual property

TYPICAL MALFUNCTION THRESHOLDS


Boost converter
Overvoltage

COMPONENT OPERATING RANGE


Boost converter
DTC P0A94 (INF 547/548) is not detected

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals. After waiting for 5 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:
Waiting for at least 5 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

1.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0A94-547 or 548 only is output.
    A
    Any of the following DTCs are also output.
    B


    DTC No.
    Relevant Diagnosis
    P0A78-266, 280
    Drive Motor "A" Inverter Performance
    P0A94-558, 559, 588, 589
    DC / DC Converter Performance
    P0A95-123
    High Voltage Fuse
    P0ADB-227
    Hybrid Battery Positive Contactor Control Circuit Low
    P0ADC-226
    Hybrid Battery Positive Contactor Control Circuit High
    P0ADF-229
    Hybrid Battery Negative Contactor Control Circuit Low
    P0AE0-228
    Hybrid Battery Negative Contactor Control Circuit High
    P3004-803
    Power Cable Malfunction

    HINT:
    1. *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic flowchart.
    2. Turning the power switch on (IG) with the service plug grip and inverter cover removed causes interlock switch system DTC P0AD-350 output.
    3. P0A94-547 and P0A94-548 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.



B
GO TO DTC CHART (Click here)
A


2.CHECK CONNECTOR CONNECTION CONDITION (MG ECU CONNECTOR)

CAUTION:
Be sure to wear insulated gloves.

  1. Turn the power switch off.

  1. Remove the service plug grip (Click here).

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the inverter cover (Click here).

    NOTICE:
    1. Wrap the round interlock terminal for the inverter cover with insulating tape to prevent it from shorting to ground.
    2. Be sure to prevent coolant in the inverter reserve tank from entering the inverter.
    3. Removing the inverter cover causes the MG ECU board to be exposed. Therefore, temporarily install the inverter cover for each area to be inspected.



    A170989E01
  1. Check the connections of all MG ECU connectors.

    OK:
    The connectors are connected securely and there are no contact problems.



NG
CONNECT SECURELY
OK


3.INSPECT HV RELAY ASSEMBLY (SMR2)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

  1. Remove the HV relay assembly from the vehicle (Click here).



    A108055E13
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    z30-1 - j2-1
    Power switch off
    (Auxiliary battery voltage is applied between terminals z20-1 (CON2) and z20-4 (GND))
    Below 1 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    z20-1 (CON2) - z20-4 (GND)
    Power switch off
    (at -31 to 176°F (-35 to 80°C))
    20 to 60 Ω



NG
REPLACE HV RELAY ASSEMBLY (Click here)
OK


4.INSPECT HV RELAY ASSEMBLY (SMR3)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.



    A108054E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    z31-1 - j3-1
    Power switch off
    (Auxiliary battery voltage is applied between terminals z20-2 (CON3) and z20-4 (GND))
    Below 1 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    z20-2 (CON3) - z20-4 (GND)
    Power switch off
    (at -31 to 176°F (-35 to 80°C))
    20 to 60 Ω



NG
REPLACE HV RELAY ASSEMBLY (Click here)
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)