Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Fuel Injector Circuit

for Preparation Click here


DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM


A184182E02


INSPECTION PROCEDURE

1.CHECK INJECTOR ASSEMBLY (POWER SOURCE)


    A183068E02
  1. Disconnect the injector assembly connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B13-2 - Body ground
    Power switch on (IG)
    11 to 14 V
    B14-2 - Body ground
    Power switch on (IG)
    11 to 14 V
    B15-2 - Body ground
    Power switch on (IG)
    11 to 14 V
    B16-2 - Body ground
    Power switch on (IG)
    11 to 14 V
    B17-2 - Body ground
    Power switch on (IG)
    11 to 14 V
    B18-2 - Body ground
    Power switch on (IG)
    11 to 14 V

  1. Turn the power switch off.

  1. Reconnect the injector assembly connector.



NG
Go to step 5
OK


2.INSPECT INJECTOR ASSEMBLY
  1. Inspect the injector assembly (Click here).



NG
REPLACE INJECTOR ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - HYBRID VEHICLE CONTROL ECU)


    A182708E01
  1. Disconnect the injector connectors.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Check for open:
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    B13-1 - B1-1 (#10)
    Always
    Below 1 Ω
    No. 2
    B14-1 - B1-2 (#20)
    Always
    Below 1 Ω
    No. 3
    B15-1 - B1-3 (#30)
    Always
    Below 1 Ω
    No. 4
    B16-1 - B1-4 (#40)
    Always
    Below 1 Ω
    No. 5
    B17-1 - B1-5 (#50)
    Always
    Below 1 Ω
    No. 6
    B18-1 - B2-7 (#60)
    Always
    Below 1 Ω
    Check for short:
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    B13-1 - Body ground
    Always
    10 kΩ or higher
    No. 2
    B14-1 - Body ground
    Always
    10 kΩ or higher
    No. 3
    B15-1 - Body ground
    Always
    10 kΩ or higher
    No. 4
    B16-1 - Body ground
    Always
    10 kΩ or higher
    No. 5
    B17-1 - Body ground
    Always
    10 kΩ or higher
    No. 6
    B18-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the hybrid vehicle control ECU connector.

  1. Reconnect the injector connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL INJECTOR ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
OK


4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)


    A153161E07
  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B1-7 (E01) - Body ground
    Always
    Below 1 Ω
    B1-6 (E02) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the hybrid vehicle control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - BODY GROUND)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

5.INSPECT FUSE (INJ NO. 2 FUSE)


    A179777E07
  1. Remove the INJ No. 2 fuse from engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    INJ No. 2 fuse
    Always
    Below 1 Ω

  1. Reinstall the INJ No. 2 fuse.



NG
REPLACE FUSE (INJ NO. 2 FUSE)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - FUEL INJECTOR ASSEMBLY)