Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Remote Up / Down Function does not Operate

for Preparation Click here


DESCRIPTION

With the power switch on (IG) , the power window regulator master switch transmits remote switch signals to the regulator switch of the passenger door power window. Then, the regulator switch drives the passenger power window regulator motor.

WIRING DIAGRAM


B175978E03


INSPECTION PROCEDURE

1.CHECK POWER WINDOW MASTER SWITCH


    B141161
  1. Turn the window lock switch OFF and operate the switches on the master switch. Check that the remote UP / DOWN function operates normally.

    OK:
    Remote UP / DOWN function operates normally.



NG
Go to step 2
OK

END 

2.CHECK MANUAL UP / DOWN FUNCTION
  1. Check that the passenger door power window manual UP / DOWN function operates normally.

    OK:
    Manual UP / DOWN function operates normally.



NG
Go to step 3
OK

REPLACE POWER WINDOW MASTER SWITCH (Click here)  

3.HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - BATTERY AND BODY GROUND)


    B175979E01
  1. Disconnect the M1 connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    M1-6 (B) - Body ground
    Power switch on (IG)
    11 to 14 V

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    M1-1 (E) - Body ground
    Always
    Below 1 Ω



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSY
OK


4.INSPECT POWER WINDOW MASTER SWITCH


    B164359E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    6 (B) - 16 (U)
    15 (D) - 1 (E)
    UP (Passenger side)
    Below 1 Ω
    6 (B) - 15 (D)
    16 (U) - 1 (E)
    DOWN (Passenger side)
    Below 1 Ω
    6 (B) - 12 (U)
    13 (D) - 1 (E)
    UP (Rear LH)
    Below 1 Ω
    6 (B) - 13 (D)
    12 (U) - 1 (E)
    DOWN (Rear LH)
    Below 1 Ω
    6 (B) - 10 (U)
    18 (D) - 1 (E)
    UP (Rear RH)
    Below 1 Ω
    6 (B) - 18 (D)
    10 (U) - 1 (E)
    DOWN (Rear RH)
    Below 1 Ω



NG
REPLACE POWER WINDOW MASTER SWITCH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - FRONT PASSENGER, REAR LH/RH SWITCH)


    B175975E01
  1. Front passenger side:

    1. Disconnect the M1 and G7 connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      M1-16 (U) - G7-5 (SU)
      Always
      Below 1 Ω
      M1-15 (D) - G7-2 (SD)
      Always
      Below 1 Ω
      M1-16 (U) - Body ground
      Always
      10 kΩ or higher
      M1-15 (D) - Body ground
      Always
      10 kΩ or higher



    B175975E02
  1. for Rear LH side:

    1. Disconnect the M1 and K2 connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      M1-12 (U) - K2-5 (SU)
      Always
      Below 1 Ω
      M1-13 (D) - K2-2 (SD)
      Always
      Below 1 Ω
      M1-12 (U) - Body ground
      Always
      10 kΩ or higher
      M1-13 (D) - Body ground
      Always
      10 kΩ or higher



    B175975E03
  1. for Rear RH side:

    1. Disconnect the M1 and J2connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      M1-10 (U) - J2-5 (SU)
      Always
      Below 1 Ω
      M1-18 (D) - J2-2 (SD)
      Always
      Below 1 Ω
      M1-10 (U) - Body ground
      Always
      10 kΩ or higher
      M1-18 (D) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW SWITCH (APPLICABLE LOCATION)