Home › SUSPENSION & AXLE › SUSPENSION › REAR SHOCK ABSORBER

REAR SHOCK ABSORBER > INSTALLATION

for Preparation Click here



1. INSTALL REAR LOWER COIL SPRING INSULATOR


    C166023E01
  1. Install the rear lower coil spring insulator onto the rear shock absorber assembly.

    NOTICE:
    Fit the recessed part of the rear lower coil spring insulator into the recession on the shock absorber assembly.



2. INSTALL REAR NO. 1 SPRING BUMPER


    C166020
  1. Install the rear No. 1 spring bumper to the rear shock absorber assembly.



3. TEMPORARILY INSTALL REAR COIL SPRING


  1. Using SST, compress the rear coil spring.


    C166014E01

    SST
    09727-30021   (09727-00010, 09727-00021, 09727-00031)

    NOTICE:
    Do not use an impact wrench. It will damage SST.



    C166019
  1. Temporarily install the rear coil spring together with SST to the rear shock absorber assembly.



4. INSTALL REAR SUSPENSION SUPPORT ASSEMBLY


    C166212E01
  1. Install the rear suspension support assembly to the rear shock absorber assembly.

    HINT:
    Align the cutout on the rear shock absorber assembly with the protrusion on the rear suspension support assembly by referring to the illustration.



5. INSTALL REAR SUPPORT TO REAR SHOCK ABSORBER COLLAR


    C166017
  1. Install the rear support to rear shock absorber collar to the rear shock absorber assembly.



6. TEMPORARILY INSTALL REAR SUPPORT TO REAR SHOCK ABSORBER NUT


    C166015
  1. Temporarily install the rear support to rear shock absorber nut to the rear shock absorber assembly.



7. INSTALL REAR COIL SPRING


  1. Install the rear coil spring.


    C166213E01

    NOTICE:
    1. Do not use an impact wrench. It will damage SST.
    2. Make sure that the end of the rear coil spring is positioned in the depression of the rear lower coil spring insulator.
    3. Ensure that the stud bolt is positioned 3.5° to the outside of the vehicle as shown in the illustration. The deviation should be within +/-5°.



8. INSTALL REAR SHOCK ABSORBER WITH COIL SPRING


    C166012
  1. Install the rear shock absorber with coil spring with the 3 nuts.

    Torque:
    58 N*m{ 591 kgf*cm , 43 ft.*lbf }



    C166010
  1. Install the rear shock absorber with coil spring with the 2 bolts and 2 nuts.

    Torque:
    290 N*m{ 2956 kgf*cm , 213 ft.*lbf }

    NOTICE:
    Keep the bolts from rotating when installing the nuts.



    C166011
  1. Fully tighten the rear support to rear shock absorber nut.

    Torque:
    55 N*m{ 561 kgf*cm , 40 ft.*lbf }



9. INSTALL REAR NO. 1 SUSPENSION SUPPORT COVER


    C166225
  1. Install the rear No. 1 suspension support cover.



10. INSTALL REAR STABILIZER LINK ASSEMBLY


    C166214E02
  1. Install the rear stabilizer link assembly to the rear shock absorber with coil spring with the nut.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.



11. INSTALL REAR SPEED SENSOR


    C166254
  1. Install the rear speed sensor to the rear shock absorber with coil spring with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    NOTICE:
    Do not twist the rear speed sensor wire when installing it.



12. INSTALL REAR FLEXIBLE HOSE


    C166009
  1. Install the rear flexible hose to the rear shock absorber with coil spring with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Do not twist the rear flexible hose when installing it.



13. INSTALL DECK SIDE TRIM


    B173624
  1. Engage the 3 guides and 4 claws as shown in the illustration.



    B173596
  1. Install the deck side trim LH with the bolt.



14. INSTALL DECK SIDE TRIM COVER


    B175144
  1. Engage the 2 claws and install the deck side trim cover LH.



15. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



16. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

HINT:
Click here