FRONT SEAT INNER BELT ASSEMBLY > INSTALLATION |
| 1. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Power Seat) |
![]() |
Install the front seat inner belt assembly with the nut.
Connect each connector and clamp.
| 2. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Manual Seat) |
![]() |
Install the front seat inner belt assembly with the nut.
Connect each connector and clamp.
| 3. INSTALL FRONT SEAT ASSEMBLY (for Power Seat) |
Place the front seat assembly in the cabin.
Connect the connectors under the seat.
Connect the cable to the negative (-) battery terminal.
Temporarily install the front seat assembly with the 4 bolts.
Operate the power seat switch knob and move the seat to the rearmost position.
![]() |
Tighten the 2 bolts on the front side of the seat.
Operate the power seat switch knob and move the seat to the foremost position.
![]() |
Tighten the 2 bolts on the rear side of the seat.
| 4. INSTALL REAR INNER SEAT TRACK COVER (for Power Seat) |
![]() |
Engage the 2 claws and install the rear inner seat track cover.
| 5. INSTALL REAR OUTER SEAT TRACK COVER (for Power Seat) |
![]() |
Engage the 2 claws and install the rear outer seat track cover.
| 6. INSTALL FRONT INNER SEAT TRACK COVER (for Power Seat) |
Operate the power seat switch knob and move the seat to the rearmost position.
![]() |
Engage the 2 claws and install the front inner seat track cover.
| 7. INSTALL FRONT OUTER SEAT TRACK COVER (for Power Seat) |
![]() |
Engage the 2 claws and install the front outer seat track cover.
| 8. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Power Seat) |
![]() |
Install the front seat headrest assembly as shown in the illustration.
| 9. INSTALL FRONT SEAT ASSEMBLY (for Manual Seat) |
Place the front seat assembly in the cabin.
Connect the connectors under the seat.
Temporarily install the front seat assembly with the 4 bolts.
Lift up the seat track adjusting handle and move the seat to the rearmost position.
![]() |
Tighten the 2 bolts on the front side of the seat.
Lift up the seat track adjusting handle and move the seat to the foremost position.
![]() |
Tighten the 2 bolts on the rear side of the seat.
| 10. INSPECT FRONT SEAT SLIDE ADJUSTER LOCK (for Manual Seat) |
During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously.
If the seat adjusters do not lock simultaneously, loosen the bolts securing the seat to adjust the adjuster position.
| 11. INSTALL REAR SEAT TRACK COVER (for Manual Seat) |
![]() |
Engage the 4 claws and install the 2 rear seat track covers.
| 12. INSTALL FRONT INNER SEAT TRACK COVER (for Manual Seat) |
Lift up the seat track adjusting handle and move the seat to the rearmost position.
![]() |
Engage the 2 claws and install the front inner seat track cover.
| 13. INSTALL FRONT OUTER SEAT TRACK COVER (for Manual Seat) |
![]() |
Engage the 2 claws and install the front outer seat track cover.
| 14. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Manual Seat) |
![]() |
Install the front seat headrest assembly as shown in the illustration.
| 15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Manual Seat) |
| 16. INSPECT FRONT SEAT ASSEMBLY (for Power Seat) |
Inspect the power seat operation.
w/ Seat Heater System:
Check the seat heater operation.
Turn the ignition switch on (IG).
Turn the seat heater switch on.
Wait 5 minutes or more and confirm that the seat surface becomes warm.
| 17. INSPECT SRS WARNING LIGHT |