Home › ENGINE › 3MZ-FE ENGINE MECHANICAL › TIMING BELT

TIMING BELT > REMOVAL

for Preparation Click here



1. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E150144
  1. Remove the nut, and the front wiper arm and blade assembly LH.



2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E150145
  1. Remove the nut, and the front wiper arm and blade assembly RH.



3. REMOVE HOOD TO COWL TOP SEAL


    E150148
  1. Disengage the 8 clips and remove the hood to cowl top seal.



4. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E150146
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal LH.



    E150147
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal RH.



  1. Remove the 2 clips.


    E150149

  1. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.



5. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E150150
  1. Disconnect the connector.

  1. Remove the 4 bolts, and the windshield wiper motor and link assembly.



6. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    C175029
  1. Disengage the 4 clamps and separate the wiper wire harness from the outer cowl top panel sub-assembly.



    C175030
  1. Remove the 8 bolts, 6 nuts, and the outer cowl top panel sub-assembly.



7. REMOVE NO. 2 ENGINE ROOM SIDE COVER LH


    A173813
  1. Remove the engine room side cover.



8. REMOVE FRONT WHEEL RH


9. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 6 bolts, 2 screws, 2 clips and No. 1 engine under cover.



10. SEPARATE FRONT FENDER LINER RH


    A109418
  1. Remove the screw and clip, and separate the front fender liner.



11. REMOVE FRONT FENDER APRON SEAL RH


    A108741
  1. Remove the 2 bolts, clip and fender apron seal RH.



12. REMOVE BATTERY
  1. Disconnect the battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Remove the bolt and battery clamp.

  1. Remove the battery and battery tray.



13. REMOVE BATTERY CARRIER SUB-ASSEMBLY


    A177162
  1. Remove the 5 bolts and battery carrier.



14. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A175875
  1. Remove the 2 bolts, 4 clamps and air cleaner cap sub-assembly.

  1. Remove the air cleaner filter element from the air cleaner case.



15. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A173490
  1. Separate the No. 1 ventilation hose.



    A173491
  1. Disconnect the intake air flow meter connector.

  1. Disconnect the 2 wire harness clamps from the air cleaner case sub-assembly.



    A173492
  1. Remove the 5 bolts from the air cleaner case sub-assembly.



    A173493
  1. Loosen the hose clamp and separate the No. 1 air cleaner hose.

  1. Remove the air cleaner case sub-assembly.



16. SEPARATE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY


    A175945
  1. Disconnect the connector.

  1. Remove the 2 nuts and separate the brake master cylinder reservoir.



17. REMOVE AIR CLEANER BRACKET


    A108129
  1. Remove the 2 bolts and air cleaner bracket.



18. REMOVE ENGINE MOVING CONTROL ROD


    A181832
  1. Remove the 4 bolts, the engine moving control rod and the bracket.



19. REMOVE NO. 2 ENGINE MOUNTING STAY RH


    A108727
  1. Remove the bolt, the No. 2 engine mounting stay and the No. 2 engine mounting bracket.



20. REMOVE CRANKSHAFT PULLEY


    A108136E01
  1. Using SST, loosen the pulley bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A179525E01
  1. Using SST and the pulley bolt, remove the pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)

    NOTICE:
    Before using SST, apply lubricating oil to the threads and tip of the center bolt .



21. REMOVE NO. 1 TIMING BELT COVER
  1. Remove the 4 bolts and the No. 1 timing belt cover.



22. REMOVE NO. 2 TIMING BELT COVER


    A108158E01
  1. Disconnect the engine wire protector clamps from the No. 2 timing belt cover.

  1. Remove the 5 bolts and the timing belt cover.



23. REMOVE ENGINE MOUNTING BRACKET RH


    A108728
  1. Remove the 2 bolts, 2 nuts and engine mounting bracket RH.



24. REMOVE NO. 2 TIMING BELT GUIDE


25. REMOVE TIMING BELT


    A078326E01
  1. Set No. 1 cylinder to TDC/compression.

    1. Temporarily install the crankshaft pulley bolt and washer to the crankshaft.

    2. Turn the crankshaft clockwise, and align the timing mark of the crankshaft timing pulley with the oil pump body.



    3. A005052E01
    4. Check that the timing marks of the camshaft timing pulleys and No. 3 timing belt cover are aligned.
      If not, turn the crankshaft 1 revolution (360°).

    5. Remove the crankshaft pulley bolt.



    A052840E01
  1. If reusing the timing belt, check that there are 4 installation marks on the timing belt as shown in the illustration.

    1. If the installation marks have disappeared, put new installation marks on the timing belt before removing.



    A078327E13
  1. Set No. 1 cylinder to approximately 60° BTDC/compression.

    1. Turn the crankshaft counterclockwise by approximately 60°.

      NOTICE:
      If the timing belt is disengaged, having the crankshaft pulley at a wrong angle can cause the piston head and valve head to come into contact with each other when you remove the camshaft timing pulley and camshaft, causing damage. So always set the crankshaft pulley at the correct angle.



    A078702E01
  1. Remove the 2 bolts and No. 1 chain tensioner.

  1. Remove the timing belt in the following order.
    1st
    No. 1 idler pulley
    2nd
    RH camshaft timing pulley
    3rd
    No. 2 idler pulley
    4th
    LH camshaft timing pulley
    5th
    Water pump pulley
    6th
    Crankshaft timing pulley