Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Radio Broadcast cannot be Received or Poor Reception

for Preparation Click here


INSPECTION PROCEDURE

1.CHECK NAVIGATION RECEIVER ASSEMBLY
  1. Check the radio's automatic station search function.

    1. Check the radio's automatic station search function by activating it.

      OK:
      The radio's automatic station search function works properly.



NG
Go to step 2
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)  

2.CHECK OPTIONAL COMPONENTS
  1. Check optional components (sun-shade film, telephone antenna, etc.).

    1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

      OK:
      Optional components are installed.

      NOTICE:
      Do not remove any optional components installed by the customer without his or her consent.



NG
Go to step 3
OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE) 

3.CHECK NAVIGATION RECEIVER ASSEMBLY


    E050367
  1. Preparation for check

    1. Remove the antenna plug from the navigation receiver assembly.

  1. Check for noise

    1. Power switch on (ACC) with the navigation receiver assembly connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire, or other metal object on the navigation receiver assembly's antenna jack and check that noise can be heard from the speaker.

      OK:
      Noise occurs.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


4.CHECK GLASS ANTENNA


    E111994E01
  1. Check for continuity of the antenna.

    HINT:
    Check for continuity at the center of each antenna wire as shown in the illustration.

    NOTICE:
    When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of the negative probe and press the foil against the wire with your finger, as shown in the illustration.

    OK:
    There is continuity in the antenna.



NG
REPAIR GLASS ANTENNA (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - ANTENNA AMPLIFIER)


    E151935E02
  1. Disconnect navigation receiver assembly connector E2.



    E150785E02
  1. Disconnect antenna amplifier connector E7.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E2-13 (ANT) - E7-1 (B)
    Always
    Below 1 Ω
    E2-13 (ANT) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT NAVIGATION RECEIVER ASSEMBLY


    E150785E02
  1. Reconnect navigation receiver assembly connector E2.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E7-1 (B) - Body ground
    Power switch on (IG)
    Radio switch ON
    11 to 14 V



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


7.CHECK ANTENNA CORD
  1. Remove the antenna plug of the navigation receiver assembly and antenna.

  1. Measure the resistance between the antenna and navigation receiver assembly to check for an open circuit in the antenna cord.

    Standard resistance:
    Below 1 Ω

  1. Measure the resistance between the antenna cord and body ground to check for a short circuit in the antenna cord.

    Standard resistance:
    10 kΩ or higher



NG
REPLACE ANTENNA CORD (Click here)
OK


8.REPLACE ANTENNA AMPLIFIER
  1. Replace the antenna amplifier and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

NORMAL OPERATION