Home › ENGINE › 3MZ-FE FUEL › FUEL PUMP

FUEL PUMP > INSTALLATION

for Preparation Click here



1. INSTALL FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE


    A154761
  1. Install a new gasket to the fuel pump assembly.

  1. Install the fuel pump assembly.



    A108225
  1. Install the fuel tank vent tube set plate by aligning it with the cutout on the fuel pump assembly.

  1. Install the fuel tank vent tube set plate and fuel pump connector plate with the 8 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



    A178849E01
  1. Connect the fuel pump tube with the tube joint clip and clamp.

    NOTICE:
    1. Check that there are no scratches or foreign objects on the connecting part.
    1. Check that the fuel tube joint is inserted securely.
    1. Check that the tube joint clip is on the collar of the fuel tube joint.
    1. After installing the tube joint clip, check that the fuel tube joint is not pulled off.



    A108215E03
  1. Connect the fuel tank wire connector (A).

  1. Connect the vapor pressure sensor connector and clamp (B).



2. INSTALL FUEL TANK ASSEMBLY


    A175802E01
  1. Set the fuel tank on a transmission jack.

  1. Operate the transmission jack, and install the fuel tank to the vehicle.

  1. Operate the transmission jack, and connect the fuel tank inlet pipe with the tube connector and clamp.



    A175803
  1. Install the 2 fuel tank bands with the 4 bolts.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



3. CONNECT NO. 1 FUEL TANK BREATHER TUBE


    A108208E03
  1. Connect the fuel tank breather tube.

    1. Push in the tube connector to the pipe until the tube connector makes a "click" sound.

      NOTICE:
      1. Check for damage or foreign objects on the connected part of the fuel pipe.
      2. After connecting, check that the fuel tube connector and the pipe are securely connected by pulling on them.

  1. Install the checker to the pipe.



4. CONNECT FUEL PUMP TUBE SUB-ASSEMBLY


    A112345E02
  1. Connect the fuel pump tube sub-assembly.

    1. Push in the fuel tube connector to the pipe and push up the retainer to engage the claws.

      NOTICE:
      1. Check for damage or foreign objects on the connected part.
      2. After connecting, check that the fuel tube connector and the pipe are securely connected by pulling on them.



5. CONNECT FUEL TANK VENT HOSE


    A175818
  1. Align the quick connector with the pipe, then push in the quick connector until the retainer makes a "click" sound to connect the fuel tank vent hose to the fuel vapor containment valve.

    NOTICE:
    1. Check for scratches or foreign objects around the connected part of the quick connector and pipe before this work.
    2. After connecting the charcoal canister fuel hose, check that the charcoal canister fuel hose is securely connected by pulling on the quick connector.



6. CONNECT FUEL TANK WIRE


    A108210
  1. Connect the fuel tank wire connectors, and install them to the bracket.



7. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY


    A175800
  1. Install the No. 3 parking brake cable assembly with the nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



8. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY


    A175799
  1. Install the No. 1 fuel tank protector sub-assembly with the screw and the 4 grommets.



9. INSTALL NO. 3 FRONT FLOOR HEAT INSULATOR


    A175798
  1. Install the No. 3 front floor heat insulator with the 5 nuts.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf }



10. INSTALL CENTER EXHAUST PIPE ASSEMBLY



11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



12. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the Techstream to the DLC3.

    2. Turn the power switch on (IG) and push the Techstream main switch on.

      NOTICE:
      Do not start the engine.

    3. Select the following menu items: Power train / Engine / Active Test / Control the Fuel Pump Speed.

    4. Check for pressure in the fuel inlet tube from the fuel line. Check that sound of fuel flowing in the fuel tank can be heard. If no sound can be heard, check the integration relay, fuel pump, hybrid vehicle control ECU and wiring connector.

    5. Check that there are no fuel leaks anywhere on the fuel system after performing maintenance.

  1. Inspect for fuel leaks.

    1. Check that there are no fuel leaks anywhere on the system after performing maintenance. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the power switch off.

  1. Disconnect the Techstream from the DLC3.



13. INSPECT FOR EXHAUST GAS LEAK


14. INSTALL FRONT CENTER FLOOR COVER


15. INSTALL FRONT FLOOR COVER LH