Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

NAVIGATION SYSTEM > DIAGNOSIS DISPLAY DETAILED DESCRIPTION

for Preparation Click here


HINT:
  1. This section contains a detailed description of displays in diagnostic mode.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


SYSTEM CHECK


  1. System Check Mode Screen


    E136181E04


    1. Device Names and Hardware Address/*1

      HINT:
      1. Registered device names are displayed.
      2. If a device name is unknown to the system, its physical address is shown instead.

      Address No.
      Name
      Address No.
      Name
      110
      EMV
      120
      AVX
      128
      1DIN TV
      140
      AVN
      144
      G-BOOK
      178
      NAVI
      17C
      MONET
      190
      AUDIO H/U
      1AC
      CAMERA-C
      1B0
      Rr-TV
      1C0
      Rr-CONT
      19D
      BT-HF
      1C4
      PANEL
      1C6
      G/W
      1C8
      FM-M-LCD
      1D8
      CONT-SW
      1EC
      Body
      118
      EMVN
      1F1
      XM
      1F2
      SIRIUS
      230
      TV-TUNER
      240
      CD-CH2
      250
      DVD-CH
      280
      CAMERA
      360
      CD-CH1
      3A0
      MD-CH
      17D
      TEL
      440
      DSP-AMP
      530
      ETC
      1F6
      RSE
      1A0
      DVD-P
      1D6
      CLOCK
      238
      DTV
      480
      AMP

    2. Check Result/*2

      HINT:
      Result codes for all devices are displayed.

      Result
      Meaning
      Action
      OK
      The device does not respond with a DTC (excluding communication DTCs from the AVC-LAN).
      -
      EXCH
      The device responds with a "replace"-type DTC.
      Look up the DTC in "Unit Check Mode" and replace the device.
      CHEK
      The device responds with a "check"-type DTC.
      Look up the DTC in "Unit Check Mode".
      NCON
      The device was previously present, but does not respond in diagnostic mode.
      1. Check power supply wire harness of the device.
      2. Check the AVC-LAN of the device.
      Old
      The device responds with an "old"-type DTC.
      Look up the DTC in "Unit Check Mode".
      NRES
      The device responds in diagnostic mode, but gives no DTC information.
      1. Check power supply wire harness of the device.
      2. Check the AVC-LAN of the device.

    3. Code Clear/*3

      1. Present DTCs are cleared.
      2. Press the "Code CLR" switch for 3 seconds.

    4. Memory Clear/*4

      1. Present and past DTCs and registered connected device names are cleared.
      2. Press the "Memory CLR" switch for 3 seconds.



  2. Diagnosis MENU Screen


    E120070E01

    HINT:
    Each item is grayed out or not displayed based on the device settings.



  3. Unit Check Mode Screen


    E136182E02


    Screen Description: 
    Display
    Contents
    Device name/*1
    Target device
    Segment/*2
    Target device logical address
    DTC/*3
    DTC (Diagnostic Trouble Code)
    Timestamp/*4
    The time and date of past DTCs are displayed. (The year is displayed in 2-digit format.)
    Present code/*5
    DTCs output in the service check are displayed.
    Past code/*6
    Diagnostic memory results and recorded DTCs are displayed.
    Diagnosis clear switch/*7
    Pushing this switch for 3 seconds clears the diagnostic memory data of the target device. (Both response to diagnostic system check result and the displayed data are cleared.)



  4. LAN Monitor (Original) Screen


    E136183E04


    1. Check Result/*1

      HINT:
      Check results of all the devices are displayed.

      Result
      Meaning
      Action
      No Err (OK)
      There are no communication DTCs.
      -
      CHEK
      The device responds with a "check"-type DTC.
      Look up the DTC in "Unit Check Mode".
      NCON
      The device was previously present, but does not respond in diagnostic mode.
      1. Check power supply wire harness of the device.
      2. Check the AVC-LAN of the device.
      Old
      The device responds with an "old"-type DTC.
      Look up the DTC in "Unit Check Mode".
      NRES
      The device responds in diagnostic mode, but gives no DTC information.
      1. Check power supply wire harness of the device.
      2. Check the AVC-LAN of the device.



  5. LAN Monitor (Individual) Screen


    E136184E02


    Screen Description: 
    Display
    Contents
    Device name/*1
    Target device
    Segment/*2
    Target logical address
    DTC/*3
    DTC (Diagnostic Trouble Code)
    Sub-code (device address)/*4
    Physical address stored with DTC (If there is no address, nothing is displayed.)
    Connection check No./*5
    Connection check number stored with DTC
    DTC occurrence/*6
    Number of times the same DTC has been recorded
    Diagnosis clear switch/*7
    Pushing this switch for 3 seconds clears the diagnostic memory data of the target device. (Both response to diagnostic system check result and the displayed data are cleared.)


DISPLAY CHECK


  1. Vehicle Signal Check Mode Screen


    E120073


    Screen Description: 
    Display
    Contents
    Battery
    Battery voltage is displayed.
    PKB
    Parking brake ON/OFF state is displayed.
    REV
    Reverse signal ON/OFF state is displayed.
    IG
    IG switch ON/OFF state is displayed.
    TAIL
    TAIL signal (Light control switch) ON/OFF state is displayed.
    SPEED
    Vehicle speed is displayed in km/h.

    HINT:
    1. Only items sending vehicle signals will be displayed.
    2. This screen is updated once per second when input signals to the vehicle are changed.



  2. CAN Connection Check Screen


    E120075E01


    Screen Description: 
    Name
    Contents
    CAN connection check result/*1
    1. For systems connected to the CAN system, the results of the CAN connection check are displayed.
    2. "NG" - The power switch is on (ACC or IG) and the CAN communication lines are malfunctioning or the CAN bus lines are not connected.
    3. "OK" - The power switch is on (ACC or IG) and the CAN communication lines are normal.
    4. Blank - CAN connection check is performed with the power switch on (ACC) or off.

    HINT:
    When the power switch is off, the bus lines are disconnected, or a malfunction occurs in the bus lines while the CAN connection check result is being displayed, the problem will be reflected on the screen in real time.


NAVIGATION CHECK


  1. Navigation Check Screen


    E120076E05

    HINT:
    Each item is grayed out or not displayed based on the device settings.



  2. GPS Information Screen


    E136195E01


    1. Satellite information/*1
      Information from a maximum of 12 satellites is displayed on the screen. This information includes the target GPS satellite number, elevation angle, direction, and signal level.

    2. Receiving condition/*2

      (DENSO model): 
      Display
      Contents
      T
      The system is receiving a GPS signal, but is not using it for location.
      P
      The system is using the GPS signal for location.
      -
      The system cannot receive a GPS signal.

      (AISIN AW model): 
      Display
      Contents
      01H
      The system cannot receive a GPS signal.
      02H
      The system is tracing a satellite.
      03H
      The system is receiving a GPS signal, but is not using it for location.
      04H
      The system is using the GPS signal for location.

      Measurement information/*3: 
      Display
      Contents
      2D
      2-dimensional location method is being used.
      3D
      3-dimensional location method is being used.
      NG
      Location data cannot be used.
      Error
      Reception error has occurred.
      -
      Any other state.

      Position information/*4 
      Display
      Contents
      Position
      Latitude and longitude information on the current position is displayed.

      Date information/*5: 
      Display
      Contents
      Date
      The date/time information obtained from GPS signal is displayed in Greenwich mean time (GMT). The last 4 digits are displayed.



  3. Vehicle Sensors Screen


    E120077E01


    Vehicle signal: 
    Display
    Contents
    REV/*1
    REV signal ON/OFF state is displayed.
    SPD/*2
    SPD signal condition is displayed.

    Sensor signal: 
    Display
    Contents
    Gyro sensor/*3
    Gyro sensor output condition is displayed (when the vehicle runs straight or is stationary, the voltage is approximately 2.5 V).

    HINT:
    Signals are updated once per second only when vehicle sensor signals are changed.



  4. Microphone & Voice Recognition Check Screen


    E125119E01


    Screen Description: 
    Display
    Contents
    Microphone input level meter/*1
    Monitors the microphone input level every 0.1 sec. and displays the results in 8 different levels.
    Recording switch/*2
    Starts recording.
    Stop switch/*3
    Stops recording.
    Play switch/*4
    Plays the recorded voice.
    Recording indicator/*5
    Comes on while recording.

    HINT:
    1. The microphone input function is on at all times when this screen is displayed.
    2. While recording or playing, the switches other than the stop switch cannot be pushed.
    3. When no voice is recorded, the play switch cannot be pushed.
    4. Recording will stop after 5 seconds or by pushing the stop switch.



  5. DVD Player Information Screen


    E120078E01


    Screen Description: 
    Display
    Contents
    Trouble code/*1
    Each code corresponding to the malfunctions is displayed. For details, refer to "Trouble Code Description".
    Occurrence time/*2
    1. The date (year, month, day) and time (hour, minute, second) when the trouble code was detected are displayed as a time stamp. (Greenwich mean time)
    2. The time data to be displayed are received from the GPS receiver.
    Trouble code clear switch/*3
    All code data being displayed are cleared by pushing this switch for 3 seconds.
    Returning switch/*4
    The previous page is displayed. If the current displayed page is the first page, this switch cannot be operated.
    Proceeding switch/*5
    The next page is displayed. If the current displayed page is the last page, this switch cannot be operated.

    Trouble Code Description: 
    Code
    Malfunction
    Countermeasure
    01
    Cannot be recognized
    Replace navigation receiver assembly.
    03
    Cannot be read
    Follow the inspection procedure for DTC 58-42 (Click here).

    HINT:
    This is a DVD player check function in the navigation receiver assembly (built-in navigation ECU).