Home › HYBRID SYSTEM · P310 › HYBRID BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0A84-123    Hybrid Battery Pack Cooling Fan 1

for Preparation Click here


DESCRIPTION


  1. The speed of the battery blower assembly is controlled by the hybrid vehicle control ECU. Battery blower assembly power is supplied from the FCTL terminal of the hybrid vehicle control ECU by the battery blower relay when it is turned on. The hybrid vehicle control ECU sends command signals (S0, S1 and S2) to each battery blower assembly to get the fan speed corresponding to the HV battery temperature. Information of the voltage applied to each battery blower assembly (VM0, VM1 and VM2) is sent to the hybrid vehicle control ECU as a monitor signal via serial communication by the battery smart unit.


    A108794E02


DTC No.
DTC Detection Condition
Trouble Area
P0A84-123
Voltage at each battery assembly (V0, V1 and V2) is out of the predetermined range in proportion to the target control voltage (1 trip detection).
  1. BATT FAN relay
  2. BATT FAN fuse
  3. Battery cooling blower assembly
  4. Battery smart unit
  5. Hybrid vehicle control ECU
  6. Wire harness or connector

WIRING DIAGRAM


A176183E02


INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (DTC P0A1F -123 IS OUT PUT)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0A1F-123 is not out put.
    A
    P0A1F-123 is also output.
    B



B
GO TO DTC CHART (P0A1F-123)
A


2.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Read output DTCs.

    Result:

    DTC output
    Proceed to
    P0A84-123 is output
    A
    P0A84-123, P0A99-123, and P0AD2-123 are output
    B



B
Go to step 9
A


3.CHECK BATTERY COOLING BLOWER ASSEMBLY

CAUTION:
Be sure to wear insulated gloves and protective goggles.

  1. Connect the Techstream to the DLC3.

  1. Select the following menu items: Powertrain / Hybrid Control / Data List / VMF Fan Motor Voltage 1 to 3 and Temp of BATT TB 1 to 8.

    HINT:
    It is easier to see the change in the VMF Fan Motor Voltage when displayed in the line chart.

  1. Perform a road test and check that there is a malfunction in the VMF Fan Motor Voltage 1 while the battery cooling blower assembly is operating. (*1)

    HINT:
    The fan operates when the battery temperature is approximately 97°F (36°C) or more.



    A173697E01
  1. Remove the battery cover and replace the battery cooling blower assembly with another battery cooling blower assembly (Click here).

  1. Install the battery cover.

  1. Select the following menu items: Powertrain / Hybrid Control / Data List / VMF Fan Motor Voltage 1 to 3 and Temp of BATT TB 1 to 8.

    HINT:
    It is easier to see the change in the VMF Fan Motor Voltage when displayed in the line chart.

  1. Perform a road test and check that a malfunction in (*1) is reproduced in another battery cooling blower assembly.

    Result:
    Result
    Proceed to
    The malfunction is reproduced in the same battery cooling blower.
    A
    The malfunction is reproduced in another battery cooling blower.
    B

    HINT:
    The battery cooling blower operates when the battery temperature is approximately 97°F (36°C) or more.



B
REPLACE BATTERY COOLING BLOWER ASSEMBLY (Click here)
A


4.CHECK HARNESS AND CONNECTOR (BATT FAN RELAY - BATTERY COOLING BLOWER ASSEMBLY)

CAUTION:
Be sure to wear insulated gloves and protective goggles.



    A173697E04
  1. Disconnect the O45 battery cooling blower assembly connector.

  1. Remove the BATT FAN relay.



    A176211E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    BATT FAN relay terminal 5 - O45-1 (IG0)
    Power switch off
    Below 1 Ω

    NOTICE:
    When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BATTERY SMART UNIT)

CAUTION:
Be sure to wear insulated gloves and protective goggles.

  1. Disconnect the z18 connector from the battery smart unit (Click here).



    A173709E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    O45-2 (VM0) - z18-3 (VM0)
    Power switch off
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    O45-2 (VM0) or z18-3 (VM0) - Body ground
    Power switch off
    10 kΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BODY GROUND)

CAUTION:
Be sure to wear insulated gloves and protective goggles.



    A173710E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O45-4 (GND0) - Body ground
    Power switch off
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - HYBRID VEHICLE CONTROL ECU)

CAUTION:
Be sure to wear insulated gloves and protective goggles.

  1. Disconnect the D36 connector from the hybrid vehicle control ECU (Click here).



    A173711E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    O45-3 (SI0) - D36-15 (SI0)
    Power switch off
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    O45-3 (SI0) or D36-15 (SI0) - Body ground
    Power switch off
    10 kΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT HYBRID VEHICLE CONTROL ECU
  1. Install the battery cover.



    A109704E23
  1. Using an oscilloscope, measure the waveform according to the condition in the table below.
    Item
    Contents
    Terminal
    D36-15 (SI0) - B1-7 (E01)
    Equipment Setting
    1 V/DIV, 50 μs/DIV
    Condition
    Power switch on (IG or READY)

    Standard:
    The waveform in the illustration can be measured.

    HINT:
    1. A and B in the DUTY waveform shown in the illustration vary depending on the cooling fan mode.
    2. Duty command value is influenced by variance in fan motors and the change of power supply voltage.
    3. Measure when the vehicle comes to a stop and an idling stop.



NG
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
OK

REPLACE BATTERY SMART UNIT (Click here)  

9.CHECK FUSE (BATT FAN)


    A176191E01
  1. Remove the BATT FAN fuse.

  1. Measure the resistance of the BATT FAN fuse.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    BATT FAN fuse
    Always
    Below 1 Ω



NG
Go to step 14
OK


10.CHECK RELAY (BATT FAN)


    A176212E01
  1. Remove the BATT FAN relay.



    B016200E42
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Connection
    Condition
    Specified Condition
    1-2
    Always
    130 to 235 Ω
    3-5
    Auxiliary battery voltage is not applied between terminals 1 and 2
    10 kΩ or more
    Auxiliary battery voltage is applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE RELAY (BATT FAN)
OK


11.CHECK HARNESS AND CONNECTOR (BATT FAN RELAY - BATT FAN FUSE)


    A199855E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    BATT FAN fuse terminal 1 - BATT FAN relay terminal 1
    Power switch off
    Below 1 Ω
    BATT FAN fuse terminal 1 - BATT FAN relay terminal 3
    Below 1 Ω

    NOTICE:
    When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.CHECK HARNESS AND CONNECTOR (BATT FAN RELAY - BATTERY COOLING BLOWER ASSEMBLY)

CAUTION:
Be sure to wear insulated gloves and protective goggles.

  1. Disconnect the O45 battery cooling blower assembly connector (Click here).



    A176211E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    BATT FAN relay terminal 5 - O45-1 (IG0)
    Power switch off
    Below 1 Ω

    NOTICE:
    When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.CHECK HARNESS AND CONNECTOR (BATT FAN RELAY - HYBRID VEHICLE CONTROL ECU)


    A176214E01
  1. Disconnect the A43 connector from the hybrid vehicle control ECU (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Switch Condition
    Specified Condition
    BATT FAN relay terminal 2 - A43-9 (FCTL)
    Power switch off
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Switch Condition
    Specified Condition
    BATT FAN relay terminal 2 or A43-9 (FCTL) -Body ground
    Power switch off
    10 kΩ or higher

    NOTICE:
    When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

14.CHECK HARNESS AND CONNECTOR (BATT FAN FUSE - BATT FAN RELAY)


    A176188E01
  1. Remove the BATT FAN relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    BATT FAN relay terminal 3 - Body ground
    Power switch off
    10 kΩ or higher

    NOTICE:
    When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



NG
Go to step 18
OK


15.CHECK HARNESS AND CONNECTOR (BATT FAN RELAY - BATTERY COOLING BLOWER ASSEMBLY)

CAUTION:
Be sure to wear insulated gloves and protective goggles.

  1. Disconnect each of the 3 battery cooling blower assembly connectors (Click here).



    A173710E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O45-1 (IG0) - Body ground
    Power switch off
    10 kΩ or higher



NG
Go to step 18
OK


16.INSPECT BATTERY COOLING BLOWER ASSEMBLY

CAUTION:
Be sure to wear insulated gloves and protective goggles.



    A109603E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Connection
    Switch Condition
    Specified Condition
    O45-1(IG0) - Body ground
    Power switch off
    10 kΩ or higher
    O46-1(IG1) - Body ground
    Power switch off
    10 kΩ or higher
    O47-1(IG2) - Body ground
    Power switch off
    10 kΩ or higher

    HINT:
    Replace the defective battery cooling blower assembly.


NEXT


17.REPLACE BATTERY COOLING BLOWER ASSEMBLY
  1. Replace the defective battery cooling blower assembly (Click here).


NEXT

REPLACE FUSE (BATT FAN) 

18.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

REPLACE FUSE (BATT FAN)