Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1825/56    Short in Front Passenger Side - Side Squib Circuit

DTC    B1826/56    Open in Front Passenger Side - Side Squib Circuit

DTC    B1827/56    Short to GND in Front Passenger Side - Side Squib Circuit

DTC    B1828/56    Short to B+ in Front Passenger Side - Side Squib Circuit

for Preparation Click here


DESCRIPTION

The front passenger side - side squib circuit consists of the center airbag sensor assembly and the front seat side airbag assembly RH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side - side squib circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1825/56
  1. The center airbag sensor assembly receives a line short circuit signal 5 times in the front passenger side - side squib circuit during primary check.
  2. Front passenger side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat side airbag assembly RH (Front passenger side - side squib)
  3. Center airbag sensor assembly
B1826/56
  1. The center airbag sensor assembly receives an open circuit signal in the front passenger side - side squib circuit for 2 seconds.
  2. Front passenger side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat side airbag assembly RH (Front passenger side - side squib)
  3. Center airbag sensor assembly
B1827/56
  1. The center airbag sensor assembly receives a short circuit to ground signal in the front passenger side - side squib circuit for 0.5 seconds.
  2. Front passenger side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat side airbag assembly RH (Front passenger side - side squib)
  3. Center airbag sensor assembly
B1828/56
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the front passenger side - side squib circuit for 0.5 seconds.
  2. Front passenger side - side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat side airbag assembly RH (Front passenger side - side squib)
  3. Center airbag sensor assembly

WIRING DIAGRAM


C157591E48


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "check mode" (signal check) with Techstream (Click here).
  2. After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).

1.CHECK CONNECTORS


    C165140E12
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the front seat side airbag assembly RH and center airbag sensor assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the front seat side airbag assembly RH and center airbag sensor assembly.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


2.CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY RH (FRONT PASSENGER SIDE - SIDE SQUIB)


    C167989E03
  1. Connect the connector to the center airbag sensor assembly.

  1. Connect SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat side airbag assembly RH (front passenger side - side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1825, B1826, B1827, B1828, or 56 is not output.

    HINT:
    Codes other than DTC B1825, B1826, B1827, B1828, and 56 may be output at this time, but they are not related to this check.

    Result 
    Result
    Proceed to
    NG
    A
    OK (for Manual Seat)
    B
    OK (for Power Seat)
    C



B
REPLACE FRONT SEAT ASSEMBLY RH (for Manual Seat) (Click here)

C
REPLACE FRONT SEAT ASSEMBLY RH (for Power Seat) (Click here)
A


3.CHECK FLOOR WIRE (FRONT PASSENGER SIDE - SIDE SQUIB CIRCUIT)


    C157614E07
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Disconnect the floor wire from the center airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      N5-1 (SFR+) - Body ground
      power switch on (IG)
      Below 1 V
      N5-2 (SFR-) - Body ground
      power switch on (IG)
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the power switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      N5-1 (SFR+) - N5-2 (SFR-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      N5-1 (SFR+) - Body ground
      Always
      1 MΩ or higher
      N5-2 (SFR-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      N5-1 (SFR+) - N5-2 (SFR-)
      Always
      1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


4.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C167990E02
  1. Restore the released activation prevention mechanism of connector B to the original condition.

  1. Connect the connectors to the front seat side airbag assembly RH and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1825, B1826, B1827, B1828, or 56 is not output.

    HINT:
    Codes other than DTC B1825, B1826, B1827, B1828, and 56 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)