DTC B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1655/37 |
|
|

| 1.CHECK CONNECTORS |
Turn the power switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and front seat inner belt assembly LH.
Disconnect the connectors from the center airbag sensor assembly and the front seat inner belt assembly LH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 2.CHECK FLOOR WIRE NO. 2 (OPEN) |
Using SST, connect terminals 10 (DBE+) and 18 (DBE-) of connector B.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O10-1 (LBE+) - O10-3 (LBE-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE NO. 2 (SHORT) |
![]() |
Disconnect SST from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O10-1 (LBE+) - O10-3 (LBE-) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE NO. 2 (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O10-1 (LBE+) - Body ground | power switch on (IG) | Below 1 V |
| O10-3 (LBE-) - Body ground | power switch on (IG) | Below 1 V |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE NO. 2 (SHORT TO GROUND) |
![]() |
Turn the power switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O10-1 (LBE+) - Body ground | Always | 1 MΩ or higher |
| O10-3 (LBE-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK FRONT SEAT INNER BELT ASSEMBLY LH |
![]() |
Connect the connectors to the center airbag sensor assembly and the front seat inner belt assembly LH.
Connect the negative (-) terminal cable to the battery.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 7.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH |
Turn the power switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the front seat inner belt assembly LH (Click here).
| NEXT | |
| 8.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the negative (-) terminal cable to the battery.
Turn the power switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||