Home › HYBRID SYSTEM ยท P310 › HYBRID TRANSMISSION / TRANSAXLE › SHIFT LEVER

SHIFT LEVER > INSTALLATION

for Preparation Click here



1. INSTALL SHIFT LEVER ASSEMBLY


    C172352E01
  1. Install the shift lever assembly with the 4 nuts.

    Torque:
    12 N*m{ 122 kgf*cm , 10 ft.*lbf }

    HINT:
    Tighten the nuts in the order of A, B, C, and D.

    NOTICE:
    Be careful not to route the indicator light or shift lock system wiring between the shift lever assembly and the floor while installing the shift lever assembly.

  1. Install the No. 2 console box mounting bracket with the 2 screws.



    C178031
  1. Connect the 2 connectors to the shift lever assembly.



2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C172351E01
  1. Connect the socket of the transmission control cable assembly to the shift lever assembly.

  1. Connect the control cable end to the shift lever assembly.

  1. Push the stopper cap to the socket as shown in the illustration.

  1. Turn the socket of the transmission control cable assembly clockwise and install the stopper cap.

    NOTICE:
    1. To prevent torsion of the inner cable, the end with protrusion should face up.
    2. Confirm that the connection between the socket and the shift lock control unit is secure.



3. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    C172350
  1. Install the shift lever knob sub-assembly.



4. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    B168374
  1. Engage the claw and 2 guides.

  1. Install the front No. 2 console box insert with the 3 screws <E> and clip.



5. INSTALL FRONT NO. 1 CONSOLE BOX INSERT


    B168373
  1. Engage the claw and 2 guides.

  1. Install the front No. 1 console box insert with the 3 screws <E> and 2 clips.



6. INSTALL CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)


    B173629
  1. Engage the 6 claws.



    B173628
  1. Install the console box assembly with the 4 bolts and 2 screws.



7. INSTALL CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)


    B175149
  1. Engage the 6 claws.

  1. Connect the connector.



    B181135
  1. Install the console box assembly with the 4 bolts and 2 screws.



8. INSTALL LOWER REAR CONSOLE BOX
  1. Install the lower rear console box.



9. INSTALL NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)


    B173013
  1. Install the No. 2 console box duct as shown in the illustration.



10. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    B168372
  1. Connect the connector.

  1. Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.



11. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Connect each connector and clamp.



    B168370
  1. Engage the 4 claws and 3 clips.

  1. Install the lower instrument panel sub-assembly with the 2 bolts <B> and 3 screws <E>.



12. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B173000
  1. Engage the 2 guides.

  1. Engage the 3 claws and install the No. 2 instrument panel under cover sub-assembly.



13. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



14. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.



15. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    B173009
  1. Connect the hood lock control cable assembly.

  1. Connect each connector and the aspirator duct.



    B173021
  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.



16. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    B173227
  1. Engage the claw and clip, install the cowl side trim sub-assembly LH.

  1. Install the clip.



17. INSTALL FRONT DOOR SCUFF PLATE LH


    B173224
  1. Engage the guide and the 8 claws, and install the front door scuff plate LH.



18. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B184681E01
  1. Apply protective tape to the areas shown in the illustration.

  1. Connect each connector.

  1. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

    NOTICE:
    Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.



19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



20. INSPECT SHIFT LEVER POSITION
  1. Apply the parking brake.

  1. Lock the wheels with chocks to secure the vehicle.

  1. Turn the power switch on (READY).

  1. Move the shift lever to the D position and release the brake pedal.

    NOTICE:
    Be sure to apply the parking brake and lock the wheels with chocks to secure the vehicle.

  1. Slowly move the shift lever to the N position and measure moving distance (a) of the shift lever from the original point to the gear activation point.

    NOTICE:
    Be sure to move the shift lever slowly.

  1. Move the shift lever to the R position and release the brake pedal.

    NOTICE:
    Be sure to apply the parking brake and lock the wheels with chocks to secure the vehicle.

  1. Slowly move the shift lever to the N position and measure moving distance (b) of the shift lever from the original point to the vehicle activation point.

    NOTICE:
    Be sure to move the shift lever slowly.



  1. Check that moving distances (a) and (b) shown in the illustration are almost the same.


    C172354E01

    HINT:
    1. If moving distances (a) and (b) are almost the same, adjustment of the shift lever position is not necessary.
    2. If moving distance (a) is shorter than (b), perform adjustment of the shift lever position [*1].
    3. If moving distance (b) is shorter than (a), perform adjustment of the shift lever position [*2].



21. ADJUST SHIFT LEVER POSITION


  1. If moving distance (a) is shorter than (b) [*1]:


    C172354E01

    HINT:
    If the shift lever is moved from the R to the N position, the moving distance of the shift lever from the original point to the gear activation point becomes longer.


    1. Move the shift lever to the N position.



    2. C108753
    3. Loosen the 2 bolts.



    4. C115287
    5. Slightly turn the shift lever position sensor counterclockwise.



    6. C108753E02
    7. Tighten the 2 bolts in the order shown in the illustration.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    8. Recheck the shift lever position.



  1. If moving distance (b) is shorter than (a) [*2]:


    C172354E01

    HINT:
    If the shift lever is moved from the D to the N position, the moving distance of the shift lever from the original point to the gear activation point becomes longer.


    1. Move the shift lever to the N position.



    2. C108753
    3. Loosen the 2 bolts.



    4. C115288
    5. Slightly turn the shift lever position sensor clockwise.



    6. C108753E02
    7. Tighten the 2 bolts in the order shown in the illustration.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    8. Recheck the shift lever position.



22. INSPECT SHIFT LEVER OPERATION
  1. While moving the shift lever from the N to each position, check that the lever moves smoothly and that the shift position indicator comes on properly according to the shift lever position.

  1. Turn the power switch on (READY), and check the following:

    1. When the shift lever is moved to the D position, the vehicle moves forward.

    2. When the shift lever is moved to the R position, the buzzer sounds and the vehicle moves in reverse.

      NOTICE:
      The vehicle should not move when the shift position indicator is off.