Home › SUSPENSION & AXLE › SUSPENSION › REAR SUSPENSION MEMBER

REAR SUSPENSION MEMBER > REMOVAL

for Preparation Click here



1. PRECAUTION
(Click here)


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE SERVICE PLUG GRIP

CAUTION:
  1. Remove the service plug to interrupt a high voltage circuit at the time of the check.
  2. Keep the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.
  3. All the high voltage wiring connectors are colored in orange.



    A175634
  1. Remove the 5 clips and door scuff plate LH.



    A175635
  1. Remove the 2 clips and reclining hinge cover.



    A175636
  1. Wear insulated glove and remove the service plug grip, after sliding up the lever of the service plug grip.

    CAUTION:
    1. Keep the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.
    2. After removing the service plug grip, do not touch the high voltage connectors and terminals for 5 minutes.

    NOTICE:
    After removing the service plug grip, do not operate the power switch as it may damage the hybrid vehicle control ECU.



4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E150144
  1. Remove the nut, and the front wiper arm and blade assembly LH.



5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E150145
  1. Remove the nut, and the front wiper arm and blade assembly RH.



6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E150146
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal LH.



    E150147
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal RH.



  1. Remove the 2 clips.


    E150149

  1. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.



7. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E150150
  1. Disconnect the connector.

  1. Remove the 4 bolts, and the windshield wiper motor and link assembly.



8. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    C175029
  1. Disengage the 4 clamps and separate the wiper wire harness from the outer cowl top panel sub-assembly.



    C175030
  1. Remove the 8 bolts, 6 nuts, and the outer cowl top panel sub-assembly.



9. REMOVE NO. 2 ENGINE ROOM SIDE COVER LH


    A173813
  1. Remove the engine room side cover.



10. REMOVE COOL AIR INTAKE DUCT SEAL
  1. Remove the 11 clips and cool air intake duct seal.



11. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A175875
  1. Remove the 2 bolts, 4 clamps and air cleaner cap sub-assembly.

  1. Remove the air cleaner filter element from the air cleaner case.



12. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A173490
  1. Separate the No. 1 ventilation hose.



    A173491
  1. Disconnect the intake air flow meter connector.

  1. Disconnect the 2 wire harness clamps from the air cleaner case sub-assembly.



    A173492
  1. Remove the 5 bolts from the air cleaner case sub-assembly.



    A173493
  1. Loosen the hose clamp and separate the No. 1 air cleaner hose.

  1. Remove the air cleaner case sub-assembly.



13. REMOVE INVERTER RESERVE TANK SUB-ASSEMBLY


    A108512
  1. Remove the 2 bolts from the inverter reserve tank sub-assembly.



14. REMOVE INVERTER COVER


    A175851
  1. Remove the bolt and interlock bracket.



    A181825E01
  1. Insulate the removed terminal with insulating tape.

    NOTICE:
    Make sure that the terminal does not stick out from the insulating tape.



    A181826
  1. Remove the 12 bolts and inverter cover.



15. CHECK TERMINAL VOLTAGE

CAUTION:
Wear insulating gloves.

NOTICE:
  1. Make sure that the inverter with converter assembly is temporarily installed before working on the inverter with converter assembly (Click here).
  2. Do not allow any foreign objects or waterdrops to enter the inverter with converter assembly.



    A108528E01
  1. Using the voltmeter, measure the voltage between the terminals of the 2 phase connectors (N-P).

    Standard voltage:
    0 V

    HINT:
    Use measuring range of DC 750 V or more on the voltmeter.



16. INSTALL INVERTER COVER


    A181826
  1. Install the inverter cover with the 12 bolts to the inverter with converter assembly.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A175851
  1. Install the interlock bracket with the bolt to the inverter with converter assembly.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



17. INSTALL INVERTER RESERVE TANK SUB-ASSEMBLY


    A108512
  1. Install the inverter reserve tank sub-assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



18. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    A173493
  1. Align the tab on the throttle body with the groove on the air cleaner hose and tighten the hose clamp.



    A173492
  1. Install the air cleaner case sub-assembly with the 5 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    A173491
  1. Connect the intake air flow meter connector.

  1. Connect the 2 wire harness clamps to the air cleaner case.



    A173490
  1. Connect the No. 1 ventilation hose.



19. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
  1. Install the air cleaner filter element to the air cleaner case.



    A175875
  1. Install the 2 bolts, 4 clamps and air cleaner cap sub-assembly.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



20. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY


    C175030E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.

    Torque:
    Nut A:
    85 N*m{ 866 kgf*cm , 63 ft.*lbf }
    Bolt B:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
    Nut C:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



    C175029
  1. Engage the 4 clamps.



21. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E150150
  1. Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.



22. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


  1. Engage the 20 claws.


    E150149

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.



    E150146
  1. Engage the 2 claws and connect the front fender to cowl side seal LH.



    E150147
  1. Engage the 2 claws and connect the front fender to cowl side seal RH.



23. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



  1. When reinstalling:



      E112237E01
    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E152618E01
  1. Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    31.9 mm (1.26 in.)

  1. Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.



24. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



  1. When reinstalling:



      E112237E01
    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E147125E01
  1. Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    25.6 mm (1.00 in.)



25. INSTALL COOL AIR INTAKE DUCT SEAL
  1. Install the cool air intake duct seal with the 11 clips.



26. INSTALL NO. 2 ENGINE ROOM SIDE COVER LH


    A173813
  1. Fit the clips and install the No. 2 engine room side cover LH.

    NOTICE:
    1. Be sure to engage the clips securely.
    2. Do not apply excessive force or do not hit the cover to engage the clips. This may cause the cover to break.



27. REMOVE REAR WHEELS


28. REMOVE TAIL EXHAUST PIPE ASSEMBLY


    A176008
  1. Remove the 2 bolts and 2 compression springs.

  1. Remove the tail exhaust pipe assembly from the exhaust pipe support.

  1. Remove the gasket from the center exhaust pipe assembly.



29. REMOVE CENTER EXHAUST PIPE ASSEMBLY


    A176009
  1. Remove the 2 bolts and 2 compression springs.

  1. Remove the center exhaust pipe from the 3 exhaust pipe supports.

  1. Remove the gasket from the front No. 3 exhaust pipe sub-assembly.



    A177272
  1. Remove the 2 bolts and exhaust pipe damper.



30. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY


    C107671E02
  1. Remove the nut and separate the No. 3 parking brake cable assembly.



31. SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:
Perform the same procedure as the No. 3 parking brake cable assembly.



32. REMOVE REAR AXLE SHAFT NUT LH


    C165539E01
  1. Using SST and a hammer, release the staked part of the rear axle shaft nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

  1. While applying the brakes, remove the rear axle shaft nut.



33. REMOVE REAR AXLE SHAFT NUT RH

HINT:
Perform the same procedure as the LH side.



34. REMOVE REAR STRUT ROD ASSEMBLY LH


    C165999
  1. Remove the 2 bolts, the 2 nuts, and the rear strut rod assembly.

    NOTICE:
    Since stopper nuts are used, loosen the bolts.



35. REMOVE REAR STRUT ROD ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



36. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


C166216E01
  1. Put matchmarks on the adjust cams and the rear suspension member sub-assembly.

  1. Remove the bolt and nut, and separate the rear No. 2 suspension arm assembly from the rear axle carrier sub-assembly.

    NOTICE:
    Since a stopper nut is used, loosen the bolt.

  1. Remove the nut, the No. 2 camber adjust cam, the rear suspension toe adjust cam sub-assembly, and the rear No. 2 suspension arm assembly.

    HINT:
    Keep the rear suspension toe adjust cam sub-assembly from rotating when removing the nut.



37. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



38. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


C171842
  1. Remove the 2 bolts, the 2 nuts, and the rear No. 1 suspension arm assembly.

    NOTICE:
    Since stopper nuts are used, loosen the bolts.



39. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



40. REMOVE REAR DRIVE SHAFT ASSEMBLY LH


    C166348E01
  1. Put matchmarks on the rear drive shaft assembly and axle hub.

    NOTICE:
    Do not punch the marks.



    C108295E02
  1. Put matchmarks on the rear drive shaft assembly and differential side gear shaft.

  1. Remove the 4 nuts, washers and separate the rear drive shaft assembly from the differential side gear shaft LH.

  1. Separate the rear drive shaft assembly LH from the rear axle hub LH.

  1. Remove the rear drive shaft assembly LH



41. REMOVE REAR DRIVE SHAFT ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



42. REMOVE NO. 3 WIRE FRAME

NOTICE:
Wear insulated gloves.



    C105713
  1. Disconnect the 2 connectors and clamp.



    C170295
  1. Remove the nut, and separate the ground cable.



    C105714
  1. Remove the nut, and separate the wire harness clamp.



    C105715
  1. Wear insulated gloves. Remove the 2 nuts, and separate the No. 3 frame wire from the rear traction motor.



43. REMOVE REAR SUSPENSION MEMBER


    C171845
  1. Support the rear suspension member with a jack.



  1. Remove the 4 nuts, 2 bolts and 2 rear lower suspension member stopper retainers.


    C171848E01

  1. Lower the rear suspension member.

  1. Remove the 2 rear upper suspension member stoppers.



44. REMOVE REAR TRACTION WITH TRANSAXLE MOTOR ASSEMBLY


    C171849E02
  1. Remove the 4 bolts, 2 upper supports, rear traction with transaxle motor assembly, and lower stoppers.



45. REMOVE DIFFERENTIAL MOUNT CUSHION


  1. Install SST to rear suspension member as shown in the illustration.


    C171853E01

    SST
    09570-24011  

    NOTICE:
    Apply a small amount of grease to the threads of SST (bolt) before use.



    C171852E01
  1. While tapping the area around the tip of arrow (A) in the illustration using a hammer, use SST to push the differential mount cushion outward as shown in the illustration.

    SST
    09570-24011  

    HINT:
    Tapping the area around the tip of arrow (A) in the illustration makes it easier to remove the differential mount cushion.



    C171854E01
  1. Install additional SST as shown in the illustration.

    SST
    09570-24011  
    09527-17011  

  1. While tapping the area around the tip of arrow (A) in the illustration using a hammer, use SST to remove the differential mount cushion.

    SST
    09570-24011  
    09527-17011  

    HINT:
    Tapping the area around the tip of arrow (A) in the illustration makes it easier to remove the differential mount cushion.



46. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION (for LH Side)


  1. Using SST, remove the rear suspension member body mounting front cushion.


    C168195E01

    SST
    09830-10010   (09830-01010, 09830-01040, 09830-01050)
    09950-40011   (09951-04020, 09952-04010, 09955-04011, 09954-04010, 09958-04011)

    NOTICE:
    1. Set the tips of the claws in the cutouts of the body mounting cushion.
    2. Securely install the spacer No. 1 to the inner cylinder of the body mounting cushion as shown in the illustration.
    3. Apply a small amount of grease to the threads of SST (center bolt) before use.
    4. Tighten SST slowly and evenly.
    5. Be careful as the body mounting cushion may fly out.
    6. The body mounting cushion cannot be reused.



47. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION (for RH Side)

HINT:
Perform the same procedure as the LH side.



48. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for LH Side)


    C168186E01
  1. Using SST, temporarily remove the rear suspension member body mounting rear cushion.

    SST
    09710-30050  
    09950-40011   (09951-04020, 09952-04010, 09953-04010, 09954-04010, 09955-04031, 09958-04011)

    NOTICE:
    1. Set the tips of the claws in the cutouts of the body mounting cushion.
    2. Securely install the spacer No. 1 to the inner cylinder of the body mounting cushion as shown in the illustration.
    3. Apply a small amount of grease to the threads of SST (center bolt) before use.
    4. Tighten SST slowly and evenly.
    5. Be careful as the body mounting cushion may fly out.
    6. The body mounting cushion cannot be reused.



    C168185E01
  1. When the mounting cushion protrudes approximately 6 mm, reassemble SST as shown in the illustration and remove the mounting cushion.

    SST
    09710-30050  
    09950-40011   (09951-04020, 09952-04010, 09953-04010, 09953-04020, 09954-04010, 09955-04031, 09958-04011)

    NOTICE:
    1. Set the tips of the claws in the cutouts of the body mounting cushion.
    2. Securely install the spacer No. 1 to the inner cylinder of the body mounting cushion as shown in the illustration.
    3. Apply a small amount of grease to the threads of SST (center bolt) before use.
    4. Tighten SST slowly and evenly.
    5. Be careful as the body mounting cushion may fly out.
    6. The body mounting cushion cannot be reused.

    HINT:
    Use the shorter center bolt first, then change it to the longer center bolt.



49. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for RH Side)

HINT:
Perform the same procedure as the LH side.



50. REMOVE HOLE PLUG
  1. Remove the 2 hole plugs.



51. REMOVE REAR NO. 2 BODY MOUNTING BRACKET SUB-ASSEMBLY LH


    C167780
  1. Remove the 3 bolts and rear No. 2 body mounting bracket sub-assembly LH.



52. REMOVE REAR NO. 2 BODY MOUNTING BRACKET SUB-ASSEMBLY RH


    C167781
  1. Remove the 3 bolts and rear No. 2 body mounting bracket sub-assembly RH.



53. REMOVE STUD BOLT (for LH Side)


    C166226
  1. Remove the stud bolt.



54. REMOVE STUD BOLT (for RH Side)

HINT:
Perform the same procedure as the LH side.