Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1660/43    Passenger Airbag ON/OFF Indicator Circuit Malfunction

for Preparation Click here


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the center airbag sensor assembly and the passenger airbag ON/OFF indicator.
The passenger airbag ON/OFF indicator indicates the operation condition of the front passenger airbag assembly, front seat side airbag assembly RH and front seat outer belt assembly RH.
DTC B1660/43 is recorded when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1660/43
  1. The center airbag sensor assembly receives an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the passenger airbag ON/OFF indicator circuit for 2 seconds.
  2. Passenger airbag ON/OFF indicator malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Instrument panel wire No. 2
  3. Navigation receiver assembly (w/ Navigation system)
  4. Hazard switch assembly (w/o Navigation system)
  5. Center airbag sensor assembly

WIRING DIAGRAM


C170266E02


INSPECTION PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
  1. Turn the power switch on (IG).



  1. Check the passenger airbag ON/OFF indicator operation.

    HINT:
    Refer to the normal condition of the passenger airbag ON/OFF indicator (Click here).


    C123768E10


    Result:

    ON/OFF Indicator Illumination
    Proceed to
    Always ON
    A
    OFF
    B



B
Go to step 9
A


2.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. w/ Navigation system:

    1. Check that the connectors are properly connected to the center airbag sensor assembly and the navigation receiver assembly. Also check that the connectors that link the instrument panel wire No. 2 and instrument panel wire are properly connected.

      OK:
      The connectors are properly connected.

      HINT:
      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    2. Disconnect the connectors from the center airbag sensor assembly and the navigation receiver assembly. Also disconnect the connectors that link the instrument panel wire No. 2 and instrument panel wire.

    3. Check that the terminals of connectors are not damaged.

      OK:
      The terminals are not deformed or damaged.

  1. w/o Navigation system:

    1. Check that the connectors are properly connected to the center airbag sensor assembly and the hazard switch assembly. Also check that the connectors that link the instrument panel wire No. 2 and instrument panel wire are properly connected.

      OK:
      The connectors are properly connected.

      HINT:
      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    2. Disconnect the connectors from the center airbag sensor assembly and the hazard switch assembly. Also disconnect the connectors that link the instrument panel wire No. 2 and instrument panel wire.

    3. Check that the terminals of connectors are not damaged.

      OK:
      The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR


    C166874E02
  1. Connect the connectors that link the instrument panel wire No. 2 and instrument panel wire.

  1. w/ Navigation system:
    Connect the connector to the navigation receiver assembly.

  1. w/o Navigation system:
    Connect the connector to the hazard switch assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Check the passenger airbag ON/OFF indicator operation.

    OK:
    The passenger airbag ON/OFF indicator does not come on.



NG
Go to step 5
OK


4.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C173750E01
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1660/43 is not output.

    HINT:
    Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (OPEN)


  1. Turn the power switch off.


    C170181E01

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. w/ Navigation system:
    Disconnect the connector from the navigation receiver assembly.

  1. w/o Navigation system:
    Disconnect the connector from the hazard switch assembly.

  1. Using SST, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting the wire.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E19-8 (PAON) - E19-9 (P-AB)
    Always
    Below 1 Ω



NG
Go to step 17
OK


6.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT)


    C170182E01
  1. Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E19-8 (PAON) - E19-9 (P-AB)
    Always
    1 MΩ or higher



NG
Go to step 18
OK


7.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT TO GROUND)


    C170182E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E19-8 (PAON) - Body ground
    Always
    1 MΩ or higher
    E19-9 (P-AB) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 19
OK


8.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT TO B+)


    C170182E01
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E19-8 (PAON) - Body ground
    power switch on (IG)
    Below 1 V
    E19-9 (P-AB) - Body ground
    power switch on (IG)
    Below 1 V

    Result:
    Result
    Proceed to
    OK (w/ Navigation system)
    A
    OK (w/o Navigation system)
    B
    NG
    C



B
REPLACE HAZARD SWITCH ASSEMBLY (Click here)

C
Go to step 20
A

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)  

9.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. w/ Navigation system:

    1. Check that the connectors are properly connected to the center airbag sensor assembly and the navigation receiver assembly. Also check that the connectors that link the instrument panel wire No. 2 and instrument panel wire are properly connected.

      OK:
      The connectors are properly connected.

      HINT:
      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    2. Disconnect the connectors from the center airbag sensor assembly and the navigation receiver assembly. Also disconnect the connectors that link the instrument panel wire No. 2 and instrument panel wire.

    3. Check that the terminals of connectors are not damaged.

      OK:
      The terminals are not deformed or damaged.

  1. w/o Navigation system:

    1. Check that the connectors are properly connected to the center airbag sensor assembly and the hazard switch assembly. Also check that the connectors that link the instrument panel wire No. 2 and instrument panel wire are properly connected.

      OK:
      The connectors are properly connected.

      HINT:
      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    2. Disconnect the connectors from the center airbag sensor assembly and the hazard switch assembly. Also disconnect the connectors that link the instrument panel wire No. 2 and instrument panel wire.

    3. Check that the terminals of connectors are not damaged.

      OK:
      The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


10.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (OPEN)


  1. Connect the connectors that link the instrument panel wire No. 2 and instrument panel wire.


    C170181E01

  1. Using SST, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting the wire.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E19-8 (PAON) - E19-9 (P-AB)
    Always
    Below 1 Ω



NG
Go to step 17
OK


11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT)


    C170182E01
  1. Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E19-8 (PAON) - E19-9 (P-AB)
    Always
    1 MΩ or higher



NG
Go to step 18
OK


12.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT TO GROUND)


    C170182E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E19-8 (PAON) - Body ground
    Always
    1 MΩ or higher
    E19-9 (P-AB) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 19
OK


13.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CIRCUIT (SHORT TO B+)


    C170182E01
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E19-8 (PAON) - Body ground
    power switch on (IG)
    Below 1 V
    E19-9 (P-AB) - Body ground
    power switch on (IG)
    Below 1 V



NG
Go to step 20
OK


14.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)


    C169196E02
  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E19-1 (B) - Body ground
    power switch on (IG)
    10 to 14 V



NG
REPLACE WIRE HARNESS (PASSENGER AIRBAG ON/OFF INDICATOR - BATTERY) OR BATTERY
OK


15.CHECK PASSENGER AIRBAG ON/OFF INDICATOR


    C169197E02
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. w/ Navigation system
    Connect the connector to the navigation receiver assembly.

  1. w/o Navigation system
    Connect the connector to the hazard switch assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Check the indicator according to the conditions in the table below.

    Indicator condition:
    Tester Connection
    Switch Condition
    Passenger Airbag ON/OFF Indicator
    D30-23 (PAON) - Body ground
    power switch on (IG)
    "ON" comes on
    D30-17 (P-AB) - Body ground
    power switch on (IG)
    "OFF" comes on

    Result:
    Result
    Proceed to
    OK
    A
    NG (w/ Navigation system)
    B
    NG (w/o Navigation system)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

C
REPLACE HAZARD SWITCH ASSEMBLY (Click here)
A


16.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C173750E01
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1660/43 is not output.

    HINT:
    Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

17.CHECK INSTRUMENT PANEL WIRE (OPEN)


  1. Disconnect the instrument panel wire from the instrument panel wire No. 2.


    C170183E01

    HINT:
    SST has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    ED5-4 (PAON) - ED5-3 (P-AB)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE INSTRUMENT PANEL WIRE NO. 2 

18.CHECK INSTRUMENT PANEL WIRE (SHORT)


    C170184E01
  1. Disconnect the instrument panel wire from the instrument panel wire No. 2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    ED5-4 (PAON) - ED5-3 (P-AB)
    Always
    1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE INSTRUMENT PANEL WIRE NO. 2 

19.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)


    C170184E01
  1. Disconnect the instrument panel wire from the instrument panel wire No. 2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    ED5-4 (PAON) - Body ground
    Always
    1 MΩ or higher
    ED5-3 (P-AB) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE INSTRUMENT PANEL WIRE NO. 2 

20.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)


    C170184E01
  1. Turn the power switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the instrument panel wire from the instrument panel wire No. 2.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    ED5-4 (PAON) - Body ground
    power switch on (IG)
    Below 1 V
    ED5-3 (P-AB) - Body ground
    power switch on (IG)
    Below 1 V



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE INSTRUMENT PANEL WIRE NO. 2