Home › CRUISE CONTROL SYSTEM › CRUISE CONTROL › CRUISE CONTROL SYSTEM

DTC    P0500    Vehicle Speed Sensor Malfunction

for Preparation Click here


DESCRIPTION

The hybrid vehicle control ECU receives a vehicle speed signal from a combination meter to control the cruise control system.
A voltage of 12 V or 5 V is output from the combination meter assembly and then input to the skid control ECU.
A voltage of 12 V or 5 V is output from each ECU or relay and then input to the combination meter assembly.
The signal is changed to a pulse signal at the transistor in the combination meter assembly.
Each ECU controls the respective system based on the pulse signal.
If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.

DTC No.
DTC Detection Condition
Trouble Area
P0500
The vehicle speed signal from the vehicle speed sensor is cut for 0.14 sec. or more while cruise control is in operation.
  1. Vehicle speed sensor
  2. Vehicle speed sensor signal circuit
  3. Combination meter assembly
  4. Wire harness or connector
  5. Hybrid vehicle control ECU

WIRING DIAGRAM


E156054E01


INSPECTION PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)


    E152386E01
  1. Remove the combination meter.

  1. Connect the oscilloscope to terminal E1-9 (+S) and body ground.

  1. Turn the power switch on (IG).

  1. Turn the wheel slowly.

  1. Check the signal waveform according to the condition(s) in the table below.
    Item
    Condition
    Tool setting
    5 V/DIV., 20 ms/DIV.
    Vehicle condition
    Driving at approx. 20 km/h (12 mph)

    OK:
    The waveform is displayed as shown in the illustration.

    HINT:
    When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



NG
GO TO SPEED SIGNAL CIRCUIT (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HYBRID VEHICLE CONTROL ECU)


    E152525E01
  1. Disconnect the E1 connector from the combination meter.

  1. Disconnect the D35 connector from the hybrid vehicle control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    E1-9 (+S) - D35-24 (SPDI)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    E1-9 (+S) or D35-24 (SPDI) - Body ground
    10 kΩ or higher

  1. Reconnect the E1 connector to the combination meter.

  1. Reconnect the D35 connector to the hybrid vehicle control ECU.



NG
Go to step 3
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - JUNCTION CONNECTOR)


    E152526E01
  1. Disconnect the D35 connector from the hybrid vehicle control ECU.

  1. Disconnect the D53 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D53-11 (SPD) - D35-24 (SPDI)
    Always
    Below 1 Ω

  1. Reconnect the D35 connector to the hybrid vehicle control ECU.

  1. Reconnect the D53 junction connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (HYBRID VEHICLE CONTROL ECU - JUNCTION CONNECTOR)
OK

REPLACE JUNCTION CONNECTOR (NO. 4 JUNCTION CONNECTOR)