Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Speed Signal Circuit

for Preparation Click here


DESCRIPTION

The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU which uses this information to create the vehicle speed sensor signal*1. The vehicle speed sensor signal consists of pulses sent to the combination meter from the skid control ECU. To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter. This voltage is sent to the skid control ECU. The pulse signal is created by switching the transistor in the skid control ECU on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter is controlled by the signal from the skid control ECU. When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter controls its respective system based on the pulse signal. *1: This vehicle speed sensor signal is created by the skid control ECU. There is no actual component that is referred to as the vehicle speed sensor. In addition, for some other systems, vehicle speed information may be exchanged using CAN communication.

HINT:
This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter operation. Combination meter components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM


E156054E01


INSPECTION PROCEDURE

1.INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)


    E146920E03
  1. Disconnect the E1 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E1-9 (+S) - Body ground
    Power switch on (READY)
    4.5 to 14 V

    HINT:
    If any of the ECUs specified in the wiring diagram supplied power to the combination meter, the combination meter will output a waveform.



NG
Go to step 4
OK


2.INSPECT COMBINATION METER (OUTPUT VOLTAGE)
  1. Reconnect the E1 combination meter connector.



    E156052E01
  1. Disconnect the A44 skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A44-22 (SP1) - Body ground
    Power switch on (READY)
    11 to 14 V



NG
Go to step 12
OK


3.INSPECT SKID CONTROL ECU (INPUT WAVEFORM)


    E152386E02
  1. Check the input waveform.

    1. Reconnect the A44 connector.

    2. Remove the combination meter assembly with the connector(s) still connected.

    3. Connect an oscilloscope to terminals E1-29 (SI) and body ground.

    4. Power switch on (READY).

    5. Turn the wheel slowly.

    6. Check the signal waveform according to the condition(s) in the table below.
      Item
      Condition
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Driving at approx. 20 km/h (12 mph)

      OK:
      The waveform is displayed as shown in the illustration.

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



NG
REPLACE SKID CONTROL ECU
OK

REPLACE COMBINATION METER (Click here)  

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - JUNCTION CONNECTOR)


    E152394E02
  1. Disconnect the junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E1-9 (+S) - E24-2
    Always
    Below 1 Ω
    E1-9 (+S) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)


  1. Check for a short in the circuit connected to the junction connector shown in the wiring diagram.

    HINT:
    If voltage is not present, the circuit (ECU) was possibly malfunctioning. This is the circuit that will be diagnosed by following the step A that follows.



      E152393E03
    1. Disconnect the junction connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      E24-4 - Body ground
      Power switch on (READY)
      4.5 to 14 V
      D53-9 (*1) - Body ground
      Power switch on (READY)
      4.5 to 14 V
      E24-1 (*2) - Body ground
      Power switch on (READY)
      4.5 to 14 V
      E24-3 (*3) - Body ground
      Power switch on (READY)
      4.5 to 14 V
      D53-11 - Body ground
      Power switch on (READY)
      4.5 to 14 V

      *1: w/ Smart Key System
      *2: for Separate Type Amplifier System
      *3: w/ Navigation System

      Result:

      Result
      Proceed to
      Voltage is not present in one circuit.
      A
      Voltage is present in all the circuits.
      B



B
REPLACE JUNCTION CONNECTOR
A


6.SYSTEM CHECK
  1. Check the circuit that did not present voltage in step 6.

    Result:

    Tester Connection
    System that uses the circuit
    Proceed to
    D53-9 - Body ground
    Smart key system
    A
    D53-11 - Body ground
    Hybrid Vehicle Control System
    B
    E24-3 (*1) - Body ground
    Navigation system
    C
    E24-4 - Body ground
    Audio/visual system
    D
    E24-1 (*2) - Body ground
    Separate type amplifier system
    E

    *1: w/ Navigation System
    *2: for Separate Type Amplifier System



B
Go to step 8

C
Go to step 9

D
Go to step 10

E
Go to step 11
A


7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU CIRCUIT)


    E125556E10
  1. Disconnect the D9 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D9-9 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU CIRCUIT)


    A174231E04
  1. Disconnect the D35 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D35-24 (SPD1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE CONTROL ECU (for 3MZ-FE)  

9.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER CIRCUIT)


    E152468E04
  1. Disconnect the E5 (*) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E5-3 (SPD) (*) - Body ground
    Always
    10 kΩ or higher

    *: w/ Navigation System



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NAVIGATION RECEIVER  

10.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY CIRCUIT)


    E152469E04
  1. Disconnect the E3 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E3-3 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY  

11.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER CIRCUIT)


    E152435E02
  1. Disconnect the N14 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N14-11 (SPD) (*) - Body ground
    Always
    10 kΩ or higher

    *: for Separate Type Amplifier System



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER  

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU)


    E156053E01
  1. Disconnect the E1 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A44-22 (SP1) - E1-29 (SI)
    Always
    Below 1 Ω
    A44-22 (SP1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER (Click here)