DTC B2342 Switch Failure |
| DTC No. | DTC Detection Condition | Trouble Area |
| B2342 | Sliding roof drive gear sub-assembly (sliding roof control ECU) detects OPEN, CLOSE, UP or DOWN switch in roof console box assembly (sliding roof switch assembly) is stuck for 30 seconds or more |
|
| 1.READ VALUE USING TECHSTREAM (SLIDE OPEN AND TILT UP SWITCH) |
Use the Data List to check if the sliding roof switch assembly is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Open Switch | Slide switch open signal/ON or OFF | ON: OPEN switch is pressed. OFF: OPEN switch is not pressed. | - |
| Close Switch | Slide switch close signal/ON or OFF | ON: CLOSE switch is pressed. OFF: CLOSE switch is not pressed. | - |
| Up Switch | Tilt switch up signal/ON or OFF | ON: UP switch is pressed. OFF: UP switch is not pressed. | - |
| Down Switch | Tilt switch down signal/ON or OFF | ON: DOWN switch is pressed. OFF: DOWN switch is not pressed. | - |
|
| ||||
| OK | |
| 2.CHECK SLIDING ROOF FUNCTION |
Check the AUTO operation with the OPEN and UP switches (Click here).
|
| ||||
| OK | |
| 3.RECHECK FOR DTC |
Delete the DTCs (Click here).
Recheck for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 4.INSPECT ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF SWITCH ASSEMBLY) |
![]() |
Remove the roof console box assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Q1-3 (CLS) - Q1-2 (GND) | CLOSE | Below 100 Ω |
| Q1-4 (OPN) - Q1-2 (GND) | OPEN | Below 100 Ω |
| Q1-5 (DOWN) - Q1-2 (GND) | DOWN | Below 100 Ω |
| Q1-6 (UP) - Q1-2 (GND) | UP | Below 100 Ω |
| Q1-3 (CLS) - Q1-2 (GND) | OPEN | 1 kΩ or higher |
| Q1-4 (OPN) - Q1-2 (GND) | CLOSE | 1 kΩ or higher |
| Q1-5 (DOWN) - Q1-2 (GND) | UP | 1 kΩ or higher |
| Q1-6 (UP) - Q1-2 (GND) | DOWN | 1 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK WIRE HARNESS (SLIDING ROOF CONTROL ECU - ROOF CONSOLE BOX ASSEMBLY) |
![]() |
Disconnect the Q12 and Q1 connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Q12-2 (E) - Q1-2 (GND) | Always | Below 1 Ω |
| Q12-7 (OPN) - Q1-4 (OPN) | Always | Below 1 Ω |
| Q12-8 (DWN) - Q1-5 (DOWN) | Always | Below 1 Ω |
| Q12-9 (CLS) - Q1-3 (CLS) | Always | Below 1 Ω |
| Q12-10 (UP) - Q1-6 (UP) | Always | Below 1 Ω |
| Q1-3 (CLS) - Body ground | Always | 10 kΩ or higher |
| Q1-4 (OPN) - Body ground | Always | 10 kΩ or higher |
| Q1-2 (GND) - Body ground | Always | Below 1 Ω |
| Q1-5 (DOWN) - Body ground | Always | 10 kΩ or higher |
| Q1-6 (UP) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.REPLACE ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF SWITCH ASSEMBLY) |
Replace the roof console box assembly (Click here).
| NEXT | |
| 7.RECHECK FOR DTC |
Delete the DTCs (Click here).
Recheck for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 8.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU) |
Check that the sliding roof drive gear sub-assembly (sliding roof control ECU) can be initialized (Click here).
|
| ||||
| OK | |
| 9.CHECK SLIDING ROOF FUNCTION |
Check the AUTO operation with the OPEN and UP switches (Click here).
|
| ||||
| OK | |
| 10.RECHECK FOR DTC |
Delete the DTCs (Click here).
Recheck for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 11.CHECK WIRE HARNESS (SLIDING ROOF CONTROL ECU - ROOF CONSOLE BOX ASSEMBLY) |
![]() |
Disconnect the Q12 and Q1 connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Q12-2 (E) - Q1-2 (GND) | Always | Below 1 Ω |
| Q12-7 (OPN) - Q1-4 (OPN) | Always | Below 1 Ω |
| Q12-8 (DWN) - Q1-5 (DOWN) | Always | Below 1 Ω |
| Q12-9 (CLS) - Q1-3 (CLS) | Always | Below 1 Ω |
| Q12-10 (UP) - Q1-6 (UP) | Always | Below 1 Ω |
| Q1-3 (CLS) - Body ground | Always | 10 kΩ or higher |
| Q1-4 (OPN) - Body ground | Always | 10 kΩ or higher |
| Q1-2 (GND) - Body ground | Always | Below 1 Ω |
| Q1-5 (DOWN) - Body ground | Always | 10 kΩ or higher |
| Q1-6 (UP) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||