Home › BODY › SLIDING ROOF › SLIDING ROOF SYSTEM

DTC    B2343    Position Initialization Incomplete

for Preparation Click here


DESCRIPTION

This DTC is output when the sliding roof drive gear sub-assembly (sliding roof control ECU) has not been initialized.

NOTICE:
When the sliding roof drive gear sub-assembly is reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized.


DTC No.
DTC Detection Condition
Trouble Area
B2343
Sliding roof drive gear sub-assembly (sliding roof control ECU) has not been initialized
  1. Sliding roof drive gear sub-assembly (sliding roof control ECU)
  2. Roof console box assembly (sliding roof switch assembly)
  3. Wire harness

WIRING DIAGRAM

Refer to DTC B2341 .

INSPECTION PROCEDURE

1.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
  1. Check that the sliding roof drive gear sub-assembly (sliding roof control ECU) can be initialized (Click here).

    OK:
    Sliding roof drive gear sub-assembly (sliding roof control ECU) can be initialized.



NG
Go to step 4
OK


2.CHECK SLIDING ROOF FUNCTION
  1. Check the AUTO operation with the OPEN and UP switches (Click here).

    OK:
    AUTO operation operates normally with the OPEN and UP switches.



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
OK


3.RECHECK FOR DTC
  1. Delete the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    HINT:
    If DTCs are detected frequently, replace the ECU.

    OK:
    DTC is not output.



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
OK

END 

4.INSPECT ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF SWITCH ASSEMBLY)


    B174030E02
  1. Remove the roof console box assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    Q1-3 (CLS) - Q1-2 (GND)
    CLOSE
    Below 100 Ω
    Q1-4 (OPN) - Q1-2 (GND)
    OPEN
    Below 100 Ω
    Q1-5 (DOWN) - Q1-2 (GND)
    DOWN
    Below 100 Ω
    Q1-6 (UP) - Q1-2 (GND)
    UP
    Below 100 Ω
    Q1-3 (CLS) - Q1-2 (GND)
    OPEN
    1 kΩ or higher
    Q1-4 (OPN) - Q1-2 (GND)
    CLOSE
    1 kΩ or higher
    Q1-5 (DOWN) - Q1-2 (GND)
    UP
    1 kΩ or higher
    Q1-6 (UP) - Q1-2 (GND)
    DOWN
    1 kΩ or higher



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF SWITCH ASSEMBLY)
OK


5.CHECK WIRE HARNESS (SLIDING ROOF CONTROL ECU - ROOF CONSOLE BOX ASSEMBLY)


    B174031E02
  1. Disconnect the Q12 and Q1 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q12-2 (E) - Q1-2 (GND)
    Always
    Below 1 Ω
    Q12-7 (OPN) - Q1-4 (OPN)
    Always
    Below 1 Ω
    Q12-8 (DWN) - Q1-5 (DOWN)
    Always
    Below 1 Ω
    Q12-9 (CLS) - Q1-3 (CLS)
    Always
    Below 1 Ω
    Q12-10 (UP) - Q1-6 (UP)
    Always
    Below 1 Ω
    Q1-3 (CLS) - Body ground
    Always
    10 kΩ or higher
    Q1-4 (OPN) - Body ground
    Always
    10 kΩ or higher
    Q1-2 (GND) - Body ground
    Always
    Below 1 Ω
    Q1-5 (DOWN) - Body ground
    Always
    10 kΩ or higher
    Q1-6 (UP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)