Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0607    Control Module Performance

for Preparation Click here


MONITOR DESCRIPTION

The ECM (included in the hybrid vehicle control ECU) continuously monitors its internal processors (CPUs), heated oxygen sensor transistors. This self-check ensures that the ECM is functioning properly.

DTC No.
DTC Detection Condition
Trouble Area
P0607
When one of following conditions is met:
  1. Hybrid vehicle control ECU CPUs malfunction
  2. Heated oxygen transistors built into hybrid vehicle control ECU malfunctions
  1. Exhaust gas leak
  2. Heated oxygen sensor
  3. Hybrid vehicle control ECU

NOTICE:
An exhaust gas leak generates noise in the HO2 sensor output. The ECM may interpret this as an HO2 sensor transistor malfunction and set P0607.


MONITOR STRATEGY


Related DTCs
P0607: Control module performance
Required sensors/components (Main)
ECM (included in the hybrid vehicle control ECU)
Required sensors/components (Related)
Accelerator pedal position sensor
Throttle position sensor
Stop light switch
Cruise control
Heated oxygen sensor
Frequency of operation
Continuous
Duration
60 seconds
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None
Engine
Running
Estimated HO2 sensor temperature
450 to 800°C (842 to 1472°F)

TYPICAL MALFUNCTION THRESHOLDS


HO2 sensor transistors
Fail

INSPECTION PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output
    A
    DTC P0607 is output
    B



B
Go to step 3
A


2.INSPECT DTC (P0136, P0137, P0138, P0156, P0157 OR P0158)
  1. Inspect the P0136, P0137, P0138, P0156, P0157 or P0158 flow chart.

    HINT:
    1. If P0136 or P0156 is output, troubleshoot for that DTC first . Then proceed to "INSPECT HYBRID VEHICLE CONTROL ECU".
    2. If P0137or P0157 is output, troubleshoot for that DTC first . Then proceed to "INSPECT HYBRID VEHICLE CONTROL ECU".
    3. If P0138 or P0158 is output, troubleshoot for that DTC first . Then proceed to "INSPECT HYBRID VEHICLE CONTROL ECU".
    4. If DTC P0606 and P0136, P0137, P0138, P0156, P0157 or P0158 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or more).



NEXT
Go to step 6

3.CHECK FOR EXHAUST GAS LEAK
  1. Allow the engine to idle and rev the engine.

  1. Check for exhaust gas leaks around the heated oxygen sensor.
    If any exhaust gas leaks are present, repair it and proceed to "PERFORM CONFIRMATION DRIVING PATTERN". If no exhaust gas leaks are present, proceed to "PERFORM CONFIRMATION DRIVING PATTERN".

    HINT:
    1. If no exhaust gas leaks are present, a malfunction in the heated oxygen sensor circuit is suspected.
    2. If any exhaust gas leaks are present around the heated oxygen sensor, noise appears in the output voltage of the heated oxygen sensor.


NEXT


4.PERFORM CONFIRMATION DRIVING PATTERN
  1. Clear the DTC (Click here).

  1. Connect the Techstream to the DLC3.

  1. Warm up the engine until the engine coolant temperature becomes 75° (167°F) or more.



  1. Perform the driving pattern.


    A144392E29

    1. Accelerate the vehicle until 50 mph (80 km/h) and stop the vehicle.

    2. Drive the vehicle by 38 to 50 mph (60 to 80 km/h) for 5 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output
    A
    DTC P0607 is output
    B
    DTC is not output
    C



B
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)

C
Go to step 6
A


5.INSPECT DTC (P0136, P0137, P0138, P0156, P0157 OR P0158)
  1. Inspect the P0136, P0137, P0138, P0156, P0157 or P0158 flow chart.

    HINT:
    1. If P0136 or P0156 is output, troubleshoot for that DTC first . Then proceed to "INSPECT HYBRID VEHICLE CONTROL ECU".
    2. If P0137or P0157 is output, troubleshoot for that DTC first . Then proceed to "INSPECT HYBRID VEHICLE CONTROL ECU".
    3. If P0138 or P0158 is output, troubleshoot for that DTC first . Then proceed to "INSPECT HYBRID VEHICLE CONTROL ECU".
    4. If DTC P0606 and P0136, P0137, P0138, P0156, P0157 or P0158 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or more).


NEXT


6.INSPECT HYBRID VEHICLE CONTROL ECU
  1. Clear the DTC (Click here).

  1. Stop the engine and wait for 30 minutes.

  1. Connect the Techstream to the DLC3.

  1. Start the engine and allow it to idle for 2 minutes.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC P0607 is output
    B



B
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
A

END