Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P050A    Cold Start Idle Air Control System Performance

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
P050A
Accumulated intake air amount 10 seconds of idling after cold start is less than threshold
(2 trip detection logic)
  1. Throttle body
  2. Mass air flow meter
  3. PCV hose
  4. Air cleaner filter
  5. Intake system
  6. VVT system
  7. Hybrid vehicle control ECU
This monitor will run when the engine is started with the engine coolant temperature at -10 to 50°C (14 to 122°F). The DTC will be set after the engine idles for 13 seconds (2 trip detection logic).
The DTC is designed to monitor the idle air control at cold start. When the engine is started with the engine coolant temperature at lower than 50°C (122°F), the ECM (included in the hybrid vehicle control ECU) measures the accumulated mass air flow at engine idling. If it does not reach the criteria within 10 seconds, the ECM interprets this as a malfunction. The MIL is illuminated and a DTC is set when the malfunction is detected in consecutive driving cycles (2 trip detection logic).
The electronic throttle control system controls the idle speed. The electronic throttle control system operates the throttle actuator to open and close the throttle valve, and adjusts the intake air amount to achieve the target idle speed.

NOTICE:
When the negative battery terminal is disconnected during inspections or repairs, the ISC (Idle Speed Control) learning values are cleared. This DTC cannot be set with the ISC learning values cleared.


A124205E09


MONITOR STRATEGY


Related DTCs
P050A: Idle speed control problem at cold
Required sensors/Components (Main)
Mass air flow meter
Required sensors/Components (Related)
Engine coolant temperature sensor
Throttle position sensor, Vehicle speed sensor
Frequency of operation
Once per driving cycle
Duration
10 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
P0010, P0020 (VVT Oil Control Valve Bank 1, 2)
P0011, P0021 (VVT System 1 - Advance)
P0012, P0022 (VVT System 1 - Retard)
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio sensor heater - Sensor 1)
P0102, P0103 (Mass Air Flow meter)
P0115, P0117, P0118 (Engine Coolant Temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient Engine Coolant Temperature for Closed Loop)
P0171, P0172, P0174, P0175 (Fuel system)
P0301, P0302, P0303, P0304, P0305, P0306 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0341, P0345, P0346 (VVT sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P2195, P2196, P2197, P2198 (Air Fuel Ratio sensor - rationality)
P2237, P2240 (Air fuel ratio sensor - open)
P2238, P2241, P2252, P2255 (Air fuel ratio sensor - low impedance)
P2239, P2242, P2253, P2256 (Air fuel ratio sensor - high impedance)
P2A00, P2A03 (Air Fuel Ratio sensor - slow response)
Battery voltage
8 V or higher
Time after engine start
3 seconds or more
Engine condition
Not cranking
Engine coolant temperature at engine start
-10°C (14°F) or more
Engine coolant temperature
-10 to 50°C (14 to 122°F)
Time after idle on started
0 seconds or more
Fuel-cut
OFF
Vehicle speed
Less than 60 km/h (37 mph)
Atmospheric pressure
76 kPa (570 mmHg) or more

TYPICAL MALFUNCTION THRESHOLDS


Accumulated mass air flow
Varies with engine coolant temperature
(Example: Less than 42 g)

INSPECTION PROCEDURE

HINT:
When viewed from the rear of the engine assembly, Bank 1 is on the right side and Bank 2 is on the leftt side.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050A)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Select the following the menu items: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P050A
    A
    P050A and other DTCs
    B

    HINT:
    If any DTCs other than P050A are output, troubleshoot those DTCs first.



NG
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
OK


2.READ VALUE USING TECHSTREAM (FUEL TRIM)

HINT:
Calculate the total fuel trim values to check the characteristic deviation of the mass air flow meter.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2.

  1. Read the values displayed on the Techstream.

  1. Add together the Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values to obtain the total fuel trim.

    OK:
    Total of Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values is between -20% and 20%.



NG
Go to step 4
OK


3.CHECK THROTTLE BODY
  1. Check for deposits around the throttle valve and throttle valve condition.

    OK:
    No deposits around throttle valve and throttle valve moves smoothly.



NG
Go to step 8

OK
Go to step 9

4.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the tester on.

  1. Warm up the engine.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).

  1. Check the engine speed while operating the oil control valve using the Techstream.

    OK:

    Tester Operation
    Specified Condition
    Oil Control Valve OFF
    Normal engine speed
    Oil Control Valve ON
    Engine idles roughly or stalls (soon after OCV switched from OFF to ON)



NG
Go to step 10
OK


5.CHECK PCV SYSTEM
  1. Allow the engine to idle.

  1. Pinch the positive crankcase ventilation (PCV) hose.

  1. Check the engine rpm.

    OK:
    The engine rpm rises when the PCV hose is pinched.



NG
Go to step 11
OK


6.CHECK AIR CLEANER FILTER
  1. Visually check that the air cleaner filter is not excessively contaminated with dirt or oil.



NG
Go to step 12
OK


7.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks in intake system.



NG
Go to step 13

OK
Go to step 14

8.REPAIR OR REPLACE THROTTLE BODY
  1. Repair or replace the throttle body (Click here).



NEXT
Go to step 15

9.REPLACE HYBRID VEHICLE CONTROL ECU
  1. Replace the hybrid vehicle control ECU (Click here).



NEXT
Go to step 15

10.CHECK AND REPAIR VVT SYSTEM


NEXT
Go to step 15

11.REPAIR OR REPLACE PCV HOSE


NEXT
Go to step 15

12.REPLACE AIR CLEANER FILTER


NEXT
Go to step 15

13.REPAIR OR REPLACE INTAKE SYSTEM


NEXT
Go to step 15

14.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).


NEXT


15.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)

NOTICE:
For this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Switch the hybrid vehicle control ECU from normal mode to check mode using the Techstream (Click here).

  1. Start the engine and let it idle for a minute.

    OK:
    Stable fast idle.

  1. Read the DTCs.

    OK:
    No DTC output.


NEXT

END