Home › BODY ELECTRICAL › DOOR LOCK › REAR DOOR LOCK

REAR DOOR LOCK > INSTALLATION

for Preparation Click here



1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    B173181
  1. Install the rear door inside locking cable assembly.



    B173180
  1. Engage the 3 claws.



2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B173179
  1. Install the rear door lock remote control cable assembly.



    B173178
  1. Engage the claw.



3. INSTALL REAR DOOR LOCK ASSEMBLY

NOTICE:
  1. When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion to the connection. This may result in a malfunction of the rear door lock assembly.

  1. Apply MP grease to the sliding parts of the rear door lock assembly.

  1. Install a new door lock wiring harness seal to the rear door lock assembly.



    B173176
  1. Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.

  1. Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

  1. Using a "TORX" socket wrench (T30), install the rear door lock assembly with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector.



4. INSTALL REAR DOOR GLASS RUN


    B173165
  1. Install the rear door glass run.



5. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    B173171
  1. Slide the rear door glass sub-assembly to install it as shown in the illustration.



6. INSTALL REAR DOOR QUARTER WINDOW GLASS
  1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.



    B173169
  1. Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.



7. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
  1. Insert the rear door window division bar sub-assembly from above.

  1. Install the rear door glass run to the rear door lower window frame sub-assembly.



    B173167
  1. Install the rear door window division bar sub-assembly with the 2 bolts and screw.



    B173164
  1. Install the rear door vent seal.



8. INSTALL REAR DOOR WEATHERSTRIP


    B173163
  1. Engage the 19 clips and install the rear door weatherstrip.



9. INSTALL REAR DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the rear door panel.



    B174207E01
  1. Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.

  1. Attach the rear door service hole cover according to the reference points on the rear door panel.

    NOTICE:
    Securely install the rear door service hole cover avoiding wrinkles and air bubbles.

  1. Connect the connector.



10. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    B173160
  1. Install the rear door inner glass weatherstrip.



11. INSTALL DOOR TRIM BOARD SUB-ASSEMBLY


    B173158
  1. Connect the rear door lock remote control cable and rear door inside locking cable to the rear door inside handle sub-assembly.

  1. Engage the 2 clamps.



    B173156
  1. Engage the rear door trim board with the 5 claws on the rear door inner glass weatherstrip.

  1. Engage the 9 clips and install the rear door trim board to the rear door panel.



    B173155E01
  1. Install the 2 screws <B>.

  1. Install the screw <A>.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }



12. INSTALL DOOR ASSIST GRIP COVER


    B172990
  1. Engage the 4 claws and install the door assist grip cover.



13. INSTALL REAR DOOR ARMREST UPPER BASE PANEL
  1. Connect the connector.



    B172988
  1. Engage the 6 claws and 2 clips and install the rear door armrest upper base panel.



14. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    B172921
  1. Engage the 3 claws to install the rear door inside handle bezel plug.



15. CONNECT NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).