Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

HYBRID CONTROL SYSTEM > EV Drive Mode Switch Circuit

for Preparation Click here


DESCRIPTION

If pattern select switch (EV mode switch) signals are input to the hybrid vehicle control ECU, the ECU sends signals to the combination meter assembly via CAN communication to turn on the EV mode light.

A175887E03

If any of the following conditions are not met, EV mode may not be turned on or the mode may be cancelled. (A buzzer sounds to indicate that the transition to EV mode is cancelled and a message is displayed on the multi-information display.)

EV Mode Entry Condition
Data List Item
Specified Condition
HV battery charge level
SOC
Approximately 50% or more
Accelerator pedal position
ACCEL DEG
Approximately 40% or less
Engine coolant temperature
COOLANT TEMP
176°F (80°C) or more
HV battery temperature
BATT TEMP 1 to 4
50 to 104°F (10 to 40°C)
Vehicle speed
-
25 mph (40 km/h) or less after the engine is warmed up
Defroster
-
OFF
Cruise control
-
OFF
Win (Watts in)
WIN
-10000 W or less
Wout (Watts out)
WOUT
20000 W or more

INSPECTION PROCEDURE

1.ASK ABOUT VEHICLE CONDITION
  1. Ask the customer if a buzzer sounded to indicate that the transition to EV mode was cancelled and a message was displayed on the multi-information display when they pressed the pattern select switch assembly (EV mode switch).

    Result:

    Result
    Proceed to
    No buzzer sounded and no message was displayed on the multi-information display.
    A
    A buzzer sounded and a message was displayed on the multi-information display.
    B

    HINT:
    If a buzzer sounds and a message is displayed on the multi-information display, one or more of the EV mode entry conditions have not been met. Check that all of the EV mode entry conditions have been met before pressing the pattern select switch assembly (EV mode switch).



B
COMPLETED
A


2.READ VALUE USING TECHSTREAM (CAN BUS CHECK)

HINT:
ECUs that are correctly connected to the CAN communication system can be displayed on the Techstream.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: System Select / CAN Bus Check.

    Result:

    Result
    Proceed to
    All of the ECUs and sensors that are currently connected to the CAN communication system are displayed.
    A
    None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed.
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


3.CHECK DTC OUTPUT (ALL DTC CODE)
  1. Check for DTCs of all systems by following the prompts on the tester screen.

    Result:
    Result
    Proceed to
    No DTCs are output.
    A
    DTCs other than hybrid control system DTCs are output.
    B



B
GO TO DTC CHART
A


4.PERFORM ACTIVE TEST USING TECHSTREAM (COMBINATION METER)
  1. Select the following menu items: Body Electrical / Combination Meter / Active Test / Indicat. EV Mode.

  1. Perform the "Indicat. EV Mode" active test.

    OK:

    Tester Display
    Description
    Inspection Condition
    Specified Condition
    Indicat. EV Mode
    EV driver mode indicator light
    EV DRIVE MODE
    Comes on

    Result:
    Result
    Proceed to
    The EV mode light comes on.
    A
    The EV mode light does not come on.
    B



B
GO TO METER SYSTEM (Click here)
A


5.CHECK PATTERN SELECT SWITCH ASSEMBLY (EV MODE SWITCH)
  1. Turn the power switch off.

  1. Disconnect the pattern select switch assembly (EV mode switch) connector.



    A174904E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (B) - 1 (E)
    EV mode switch on
    Below 1 Ω
    4 (B) - 1 (E)
    EV mode switch off
    10 kΩ or higher



NG
REPLACE PATTERN SELECT SWITCH ASSEMBLY (EV MODE SWITCH)
OK


6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)
  1. Connect the pattern select switch assembly (EV mode switch) connector.

  1. Disconnect connector D35 from the hybrid vehicle control ECU.



    A174231E07
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D35-17 (EVSW) - Body ground
    EV mode switch on
    Below 1 Ω
    D35-17 (EVSW) - Body ground
    EV mode switch off
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)