Home › BODY › EXTERIOR › FRONT DOOR BELT MOULDING

FRONT DOOR BELT MOULDING > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY


    B172792
  1. Engage the 6 claws and install the front door belt moulding assembly.



2. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding parts of the front door window regulator sub-assembly.



    B172943E02
  1. Install the temporary bolt to the front door window regulator sub-assembly.

  1. Temporarily install the window regulator.

  1. Tighten the 6 bolts in the order shown in the illustration to install the front window regulator.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


    B187096E01
  1. Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated in the order of the arrows in the illustration.



    B172941
  1. Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B172940
  1. Install the hole plug.



4. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the front door panel.

  1. Pass the front door lock remote control cable and rear door inside the locking cable through a new front door service hole cover.



    B172973E01
  1. Attach the front door service hole cover according to the reference points on the front door panel.

    NOTICE:
    Securely install the front door service hole cover avoiding wrinkles and air bubbles.



    B172939
  1. Connect each connector.

  1. Engage the 2 clamps.



5. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER


    B173465E01
  1. Engage the claw, and temporarily install the outer rear view mirror assembly with cover.

  1. Tighten the 3 nuts in the order shown in the illustration to install the outer rear view mirror assembly with cover.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B173464
  1. Engage the clamp and connect the connector.

  1. Install the clip.



6. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY


    E150556
  1. Install the front No. 1 speaker assembly with the 4 bolts.

    NOTICE:
    Do not touch the cone part of the speaker.

  1. Connect the connector.



7. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP


    B172938
  1. Install the front door inner glass weatherstrip.



8. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
  1. Connect the connector.



    B172935
  1. Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.

  1. Engage the 2 clamps.



    B172933
  1. Engage the front door trim board with the 5 claws on the front door inner glass weatherstrip.

  1. Engage the 9 clips.



    B172932E01
  1. Install the 2 screws <B>.

  1. Install the screw <A> and front door trim board to the front door panel.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }



9. INSTALL COURTESY LIGHT ASSEMBLY
  1. Connect the connector.



    B172930
  1. Engage the claw and install the courtesy light assembly.



10. INSTALL ASSIST GRIP COVER


    B172925
  1. Engage the 4 claws and install the assist grip cover.



11. INSTALL FRONT ARMREST UPPER BASE PANEL
  1. Connect the connector.



    B172923
  1. Engage the 7 claws and clip and install the front armrest upper base panel.



12. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B172921
  1. Engage the 3 claws and install the front door inside handle bezel plug.



13. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


    B172931
  1. Engage the clip and claw, and install the front door lower frame bracket garnish.



14. CONNECT NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



15. INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side)
(Click here)