Home › BODY › EXTERIOR › REAR DOOR BELT MOULDING

REAR DOOR BELT MOULDING > INSTALLATION

for Preparation Click here



1. INSTALL REAR DOOR BELT MOULDING ASSEMBLY


    B172794
  1. Engage the 6 claws and install the rear door belt moulding assembly.



2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding parts of the rear door window regulator sub-assembly.



    B173172E02
  1. Install the temporary bolt to the rear door window regulator sub-assembly.

  1. Temporarily install the window regulator.

  1. Tighten the 4 bolts in the order shown in the illustration to install the rear door window regulator.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



3. INSTALL REAR DOOR GLASS RUN


    B173165
  1. Install the rear door glass run.



4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    B173171
  1. Slide the rear door glass sub-assembly to install it as shown in the illustration.



5. INSTALL REAR DOOR QUARTER WINDOW GLASS
  1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.



    B173169
  1. Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.



6. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
  1. Insert the rear door window division bar sub-assembly from above.

  1. Install the rear door glass run to the rear door lower window frame sub-assembly.



    B173167
  1. Install the rear door window division bar sub-assembly with the 2 bolts and screw.



    B173164
  1. Install the rear door vent seal.



7. INSTALL REAR DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the rear door panel.



    B174207E01
  1. Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.

  1. Attach the rear door service hole cover according to the reference points on the rear door panel.

    NOTICE:
    Securely install the rear door service hole cover avoiding wrinkles and air bubbles.

  1. Connect the connector.



8. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    B173160
  1. Install the rear door inner glass weatherstrip.



9. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B173158
  1. Connect the rear door lock remote control cable and rear door inside locking cable to the rear door inside handle sub-assembly.

  1. Engage the 2 clamps.



    B173156
  1. Engage the rear door trim board with the 5 claws on the rear door inner glass weatherstrip.

  1. Engage the 9 clips and install the rear door trim board to the rear door panel.



    B173155E01
  1. Install the 2 screws <B>.

  1. Install the screw <A>.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }



10. INSTALL DOOR ASSIST GRIP COVER


    B172990
  1. Engage the 4 claws and install the door assist grip cover.



11. INSTALL REAR DOOR ARMREST UPPER BASE PANEL
  1. Connect the connector.



    B172988
  1. Engage the 6 claws and 2 clips and install the rear door armrest upper base panel.



12. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    B172921
  1. Engage the 3 claws to install the rear door inside handle bezel plug.



13. CONNECT NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).