SECURITY HORN ASSEMBLY > INSTALLATION |
| 1. INSTALL SECURITY HORN ASSEMBLY |
Connect the connector.
![]() |
Install the security horn assembly with the bolt.
| 2. INSTALL INVERTER WITH CONVERTER ASSEMBLY |
![]() |
Install the inverter with converter assembly with the 2 nuts and bolt.
| 3. INSTALL NO. 4 INVERTER BRACKET |
![]() |
Install the No. 4 inverter bracket with the 2 bolts.
| 4. INSTALL ENGINE ROOM RELAY BLOCK ASSEMBLY |
![]() |
Install the engine room relay block assembly.
| 5. REMOVE INVERTER COVER |
![]() |
Remove the 2 bolts and inverter cover from the inverter with converter assembly.
| 6. CONNECT NO. 3 FRAME WIRE |
![]() |
After connecting the connector, press the lever down to connect the No. 3 frame wire and install the bolt to the inverter with converter assembly.
![]() |
Connect the No. 3 frame wire (high voltage cable of the rear motor (MGR)) with new 5 bolts to the inverter with converter assembly.
| 7. CONNECT MG ECU CONNECTOR |
![]() |
Connect the 2 connectors and 2 grommets to the inverter with converter assembly.
| 8. CONNECT HIGH VOLTAGE CABLE OF FRONT MOTOR |
![]() |
Connect the high voltage cable of the generator (MG1) with new 5 bolts to the inverter with converter assembly.
![]() |
Connect the high voltage cable of the motor (MG2) with new 5 bolts to the inverter with converter assembly.
| 9. CONNECT NO. 4 ENGINE WIRE |
![]() |
Connect the No. 4 engine wire with the connector, clamp and grommet to the inverter with converter assembly.
Connect the No. 4 engine wire with the bolt to the inverter with converter assembly.
| 10. INSPECT HIGH VOLTAGE CABLE CONNECTION |
![]() |
Check that each connector and terminal is firmly installed.
| 11. INSTALL INVERTER COVER |
![]() |
Install the inverter cover with the 12 bolts to the inverter with converter assembly.
![]() |
Install the interlock bracket with the bolt to the inverter with converter assembly.
| 12. CONNECT WATER HOSE |
![]() |
Connect the water hose with the clamp to the inverter with converter assembly.
| 13. CONNECT NO. 2 ENGINE ROOM WIRE |
![]() |
Connect the No. 2 engine room wire with the nut.
Connect the clamp.
![]() |
Install the No. 2 relay block cover with the 4 claws.
![]() |
Install the engine room relay block assembly.
Install the relay block cover.
| 14. INSTALL INVERTER RESERVE TANK SUB-ASSEMBLY |
![]() |
Connect the 2 water hoses to the inverter reserve tank sub-assembly with the 2 clamps.
![]() |
Install the inverter reserve tank with the 2 bolts to the inverter with converter assembly.
| 15. CONNECT NO. 1 CIRCUIT BREAKER SENSOR |
![]() |
Connect the No. 1 circuit breaker sensor connector.
| 16. INSTALL AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Separate the No. 1 ventilation hose.
![]() |
Disconnect the intake air flow meter connector.
Disconnect the 2 wire harness clamps from the air cleaner case sub-assembly.
![]() |
Remove the 5 bolts from the air cleaner case sub-assembly.
![]() |
Loosen the hose clamp and separate the No. 1 air cleaner hose.
Remove the air cleaner case sub-assembly.
| 17. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
Install the air cleaner filter element to the air cleaner case.
![]() |
Install the 2 bolts, 4 clamps and air cleaner cap sub-assembly.
| 18. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY |
![]() |
Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.
![]() |
Engage the 4 clamps.
| 19. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
![]() |
Install the windshield wiper motor and link assembly with the 4 bolts.
Connect the connector.
| 20. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
Engage the 20 claws.

Install the cowl top ventilator louver sub-assembly with the 2 clips.
![]() |
Engage the 2 claws and connect the front fender to cowl side seal LH.
![]() |
Engage the 2 claws and connect the front fender to cowl side seal RH.
| 21. INSTALL HOOD TO COWL TOP SEAL |
![]() |
Engage the 8 clips and install the hood to cowl top seal.
| 22. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
When reinstalling:
![]() |
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 25.6 mm (1.00 in.) |
| 23. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
When reinstalling:
![]() |
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 31.9 mm (1.26 in.) |
Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.
| 24. INSTALL SERVICE PLUG GRIP |
![]() |
Wear insulated gloves, then insert the service plug.
Push down on the grip to lock.
![]() |
Close the reclining hinge cover.
![]() |
Close the rear door scuff plate LH.
| 25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 26. ADD COOLANT (for Inverter) |
| DTC Code | Detection Item |
| P0A01-725 | Motor Electronics Coolant Temperature Sensor Circuit Range / Performance |
| P0A01-726 | Motor Electronics Coolant Temperature Sensor Circuit Range / Performance |
| P0A78-284 | Drive Motor "A" Inverter Performance |
| P0A7A-322 | Generator Inverter Performance |
| P0A93-346 | Inverter Cooling System Performance |
| P0A94-553 | DC / DC Converter Performance |
| P0AEE-276 | Motor Inverter Temperature Sensor "A" Circuit Range / Performance |
| P0AEE-277 | Motor Inverter Temperature Sensor "A" Circuit Range / Performance |
| P3221-314 | Generator Inverter Temperature Sensor Circuit Range / Performance |
| P3221-315 | Generator Inverter Temperature Sensor Circuit Range / Performance |
| P3226-562 | DC/DC Boost Converter Temperature Sensor |
| P3226-563 | DC/DC Boost Converter Temperature Sensor |
![]() |
Loosen the bleeder plug shown in the illustration and connect a hose.
Add coolant to the reserve tank.
![]() |
Add coolant until the level of coolant in the hose attached to the bleeder plug reaches the same level as the FULL line of the reserve tank.
When using the Techstream:
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
On the Techstream, enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.
Keep the coolant at the FULL level in the reserve tank to compensate for the drop in coolant level when the air bleeds.
When not using the Techstream:
Turn the power switch on (READY). [*1]
Turn the power switch off and add coolant to the FULL level because the coolant level drops as the air bleeds. [*2]
Repeat steps [*1] and [*2] until air bleeding from the coolant system is completed.
When the air is completely bled from the coolant system, tighten the plug.
![]() |
Add coolant to the FULL mark of the reserve tank.
| 27. INSPECT FOR COOLANT LEAK (for Inverter) |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Pump the tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and cylinder head.
| 28. INSTALL NO. 2 ENGINE ROOM SIDE COVER LH |
![]() |
Fit the clips and install the No. 2 engine room side cover LH.
| 29. INSTALL COOL AIR INTAKE DUCT SEAL |
Install the cool air intake duct seal with the 11 clips.