INSTRUMENT PANEL SAFETY PAD > REMOVAL |
| 1. PRECAUTION |
| 2. POSITION FRONT WHEELS STRAIGHT AHEAD |
| 3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 4. REMOVE LOWER NO. 3 STEERING WHEEL COVER |
![]() |
Disengage the claw and remove the lower No. 3 steering wheel cover.
| 5. REMOVE LOWER NO. 2 STEERING WHEEL COVER |
![]() |
Disengage the claw and remove the lower No. 2 steering wheel cover.
| 6. REMOVE STEERING PAD |
![]() |
Using a "TORX" socket wrench (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.
![]() |
Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand as shown in the illustration.
![]() |
Disconnect the horn connector from the steering pad.
Using a screwdriver with the tip wrapped with protective tape, disconnect the 2 airbag connectors and remove the steering pad.
| 7. REMOVE STEERING WHEEL ASSEMBLY |
![]() |
Remove the steering wheel assembly set nut.
Put matchmarks on the steering wheel assembly and the steering main shaft.
Disconnect the connectors from the spiral cable.
![]() |
Using SST, remove the steering wheel assembly.
| 8. REMOVE STEERING COLUMN COVER |
![]() |
Remove the 2 screws.
![]() |
Disengage the 2 claws to remove the lower steering column cover.
![]() |
Disengage the claw to remove the upper steering column cover.
| 9. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.
![]() |
Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly.
| 10. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
![]() |
Disengage the 4 claws and 4 clips, and remove the instrument cluster finish panel assembly.
| 11. REMOVE COMBINATION METER ASSEMBLY |
![]() |
Remove the 4 screws <E>.
Disconnect the connector and remove the combination meter assembly.
| 12. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Apply protective tape to the areas shown in the illustration.
Using a moulding remover, disengage the 2 claws and 5 clips, and then remove the center instrument panel register assembly as shown in the illustration.
| 13. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
![]() |
Apply protective tape to the areas shown in the illustration.
Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.
Disconnect each connector and remove the center instrument cluster finish panel assembly.
| 14. REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System) |
![]() |
Disengage the 4 clips and remove the heater control and accessory assembly.
Disconnect the connector.
| 15. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System) |
![]() |
Disengage the 4 clips and remove the air conditioning control assembly.
Disconnect the connector.
| 16. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System) |
![]() |
Remove the 4 bolts.
![]() |
Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.
Disconnect each connector and remove the radio receiver assembly with bracket.
| 17. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System) |
![]() |
Remove the 4 bolts.
![]() |
Pull the navigation receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.
Disconnect each connector and remove the navigation receiver assembly with bracket.
| 18. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 8 claws and guide, and remove the front door scuff plate LH.
| 19. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Remove the clip.
Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.
| 20. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY |
![]() |
Remove the 2 bolts <B>.
Disengage the 3 claws and 10 clips.
![]() |
Disconnect each connector and the aspirator duct.
Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.
| 21. REMOVE FRONT DOOR SCUFF PLATE RH |
| 22. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH |
| 23. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() |
Disengage the 3 claws.
Disengage the 2 guides and remove the No. 2 instrument panel under cover sub-assembly.
| 24. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Remove the 2 bolts <B> and 3 screws <E>.
Disengage the 4 claws and 3 clips.
Disconnect each connector and clamp, and remove the lower instrument panel sub-assembly.
| 25. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Disengage the 4 claws and 4 clips.
Disconnect the connector and remove the upper console panel sub-assembly.
| 26. REMOVE NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System) |
![]() |
Remove the No. 2 console box duct as shown in the illustration.
| 27. REMOVE LOWER REAR CONSOLE BOX |
Remove the lower rear console box.
| 28. REMOVE CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System) |
![]() |
Remove the 4 bolts and 2 screws.
![]() |
Disengage the 6 claws and remove the console box assembly.
| 29. REMOVE CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System) |
![]() |
Remove the 4 bolts and 2 screws.
![]() |
Disconnect the connector.
Disengage the 6 claws, and remove the console box assembly.
| 30. REMOVE FRONT NO. 1 CONSOLE BOX INSERT |
![]() |
Using a clip remover, remove the 2 clips.
Remove the 3 screws <E>.
Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.
| 31. REMOVE FRONT NO. 2 CONSOLE BOX INSERT |
![]() |
Using a clip remover, remove the clip.
Remove the 3 screws <E>.
Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.
| 32. REMOVE POWER SWITCH |
![]() |
Disconnect the switch connector.
Disengage the 2 claws and remove the switch.
| 33. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Remove the front door opening trim weatherstrip LH.
| 34. REMOVE FRONT PILLAR GARNISH LH |
![]() |
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 3 guides and remove the front pillar garnish LH.
Remove the clip <A>.
![]() |
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
| 35. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
| 36. REMOVE FRONT PILLAR GARNISH RH |
![]() |
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 3 guides and remove the front pillar garnish RH.
Remove the clip <A>.
![]() |
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
| 37. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Disengage the 2 claws and 2 clips.
Disengage the 2 guides and remove the No. 1 instrument panel speaker panel sub-assembly.
| 38. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side) |
![]() |
Remove the 2 bolts and front No. 2 speaker assembly.
Disconnect the connector.
| 39. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Disengage the 2 claws and 2 clips.
Disengage the 2 guides and remove the No. 2 instrument panel speaker panel sub-assembly.
| 40. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side) |
| 41. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY |
![]() |
Disconnect the connector.
| 42. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY |
Disconnect each connector.
Remove the 2 passenger airbag bolts <A>.
Disengage each clamp.

Remove the 2 clips.
Remove the 2 bolts <D> and nut <G>.
Disengage the 5 claws and remove the instrument panel safety pad assembly.

| 43. REMOVE NO. 3 INSTRUMENT PANEL STAY |
Using a screwdriver, disengage the claw and remove the 5 No. 3 instrument panel stays as shown in the illustration.

| 44. REMOVE CONSOLE BOX CUP HOLDER |
![]() |
Remove the 2 console box cup holders.
| 45. REMOVE INSTRUMENT PANEL CUP HOLDER ASSEMBLY |
![]() |
Remove the 4 screws <F> and the instrument panel cup holder assembly.
| 46. REMOVE NO. 2 CONSOLE BOX CUP HOLDER |
![]() |
Remove the No. 2 console box cup holder.