Home › BODY ELECTRICAL › LIGHTING › HEADLIGHT DIMMER SWITCH

HEADLIGHT DIMMER SWITCH > INSTALLATION

for Preparation Click here



1. INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY


    E135376
  1. Engage the claw while loosening the clamp as shown in the illustration.



    E150079
  1. Engage the clamp and install the headlight dimmer switch assembly as shown in the illustration.

  1. Connect the connector.



2. INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY


    E151096
  1. Engage the claw and install the windshield wiper switch assembly.

  1. Connect the 2 connectors.



3. INSTALL SPIRAL CABLE WITH STEERING ANGLE SENSOR
  1. Check that the front wheels are facing straight ahead.

  1. Set the turn signal switch to the neutral position.

    NOTICE:
    If it is not in the neutral position, the turn signal switch pin may be snapped.



    C165095
  1. Install the spiral cable with steering angle sensor with the 3 claws.

    NOTICE:
    When replacing the spiral cable with a new one, remove the lock pin before installing the steering wheel assembly.

  1. Connect the connectors to the spiral cable with steering angle sensor.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



4. INSTALL STEERING COLUMN COVER


    C165716
  1. Engage the claw to install the upper steering column cover.



    C166128
  1. Engage the 2 claws to install the lower steering column cover.



    C165715
  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



5. POSITION FRONT WHEELS STRAIGHT AHEAD


6. ADJUST SPIRAL CABLE SUB-ASSEMBLY
  1. Check that the power switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.



    C165096
  1. Rotate the spiral cable counterclockwise slowly by hand until it stops.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.



    C165097E01
  1. Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.

    HINT:
    The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.



7. INSTALL STEERING WHEEL ASSEMBLY


    C165708E01
  1. Align the matchmarks on the steering wheel assembly and steering main shaft.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connectors to the spiral cable sub-assembly.



8. INSPECT STEERING WHEEL CENTER POINT


9. INSTALL STEERING PAD
  1. Check that the power switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.



    C165092
  1. Support the steering pad with one hand as shown in the illustration.



    C165093
  1. Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector to the steering pad.

  1. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.



    C166982E01
  1. Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



10. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    C178264
  1. Install the lower No. 2 steering wheel cover with the claw.



11. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    C165090
  1. Install the lower No. 3 steering wheel cover with the claw.



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



13. INSPECT STEERING PAD


    C166979
  1. With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:

    1. Cuts, minute cracks or marked discoloration on the steering pad top surface or grooves.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system (Click here).



14. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).