Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › SOLAR SENSOR

SOLAR SENSOR > REMOVAL

for Preparation Click here



1. PRECAUTION
(Click here)


2. POSITION FRONT WHEELS STRAIGHT AHEAD


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment (Click here).

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



4. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    C165090
  1. Disengage the claw and remove the lower No. 3 steering wheel cover.



5. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    C178264
  1. Disengage the claw and remove the lower No. 2 steering wheel cover.



6. REMOVE STEERING PAD


    C166981E01
  1. Using a "TORX" socket wrench (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.



    C165092
  1. Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.



    C165094E01
  1. Disconnect the horn connector from the steering pad.

  1. Using a screwdriver with the tip wrapped with protective tape, disconnect the 2 airbag connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



7. REMOVE STEERING WHEEL ASSEMBLY


    C165708E01
  1. Remove the steering wheel assembly set nut.

  1. Put matchmarks on the steering wheel assembly and the steering main shaft.

  1. Disconnect the connectors from the spiral cable.



    C165709E01
  1. Using SST, remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.



8. REMOVE STEERING COLUMN COVER


    C165715
  1. Remove the 2 screws.



    C166128
  1. Disengage the 2 claws to remove the lower steering column cover.



    C165716
  1. Disengage the claw to remove the upper steering column cover.



9. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
  1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.



    C166129
  1. Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly.



10. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B168364
  1. Disengage the 4 claws and 4 clips, and remove the instrument cluster finish panel assembly.



11. REMOVE COMBINATION METER ASSEMBLY


    B168365
  1. Remove the 4 screws <E>.

  1. Disconnect the connector and remove the combination meter assembly.



12. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    B168368E01
  1. Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 2 claws and 5 clips, and then remove the center instrument panel register assembly as shown in the illustration.



13. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B184680E01
  1. Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

    NOTICE:
    Do not pull on the small storage compartment lid. Doing so may cause damage.

  1. Disconnect each connector and remove the center instrument cluster finish panel assembly.



14. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    E150367
  1. Disengage the 4 clips and remove the air conditioning control assembly.

  1. Disconnect the connector.



15. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)


    E150551
  1. Remove the 4 bolts.



    E150552
  1. Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the radio receiver assembly with bracket.



16. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)


    E150544
  1. Remove the 4 bolts.



    E150545
  1. Pull the navigation receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the navigation receiver assembly with bracket.



17. REMOVE FRONT DOOR SCUFF PLATE LH


    B173224
  1. Disengage the 8 claws and guide, and remove the front door scuff plate LH.



18. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B173227
  1. Remove the clip.

  1. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.



19. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    B173021
  1. Remove the 2 bolts <B>.

  1. Disengage the 3 claws and 10 clips.



    B173009
  1. Disconnect each connector and the aspirator duct.

  1. Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.



20. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.



21. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



22. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B172999
  1. Disengage the 3 claws.

  1. Disengage the 2 guides and remove the No. 2 instrument panel under cover sub-assembly.



23. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B168370
  1. Remove the 2 bolts <B> and 3 screws <E>.

  1. Disengage the 4 claws and 3 clips.

  1. Disconnect each connector and clamp, and remove the lower instrument panel sub-assembly.



24. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B168372
  1. Disengage the 4 claws and 4 clips.

  1. Disconnect the connector and remove the upper console panel sub-assembly.



25. REMOVE NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)


    B173012
  1. Remove the No. 2 console box duct as shown in the illustration.



26. REMOVE LOWER REAR CONSOLE BOX
  1. Remove the lower rear console box.



27. REMOVE CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)


    B173628
  1. Remove the 4 bolts and 2 screws.



    B173629
  1. Disengage the 6 claws and remove the console box assembly.



28. REMOVE CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)


    B181135
  1. Remove the 4 bolts and 2 screws.



    B175149
  1. Disconnect the connector.

  1. Disengage the 6 claws, and remove the console box assembly.



29. REMOVE FRONT NO. 1 CONSOLE BOX INSERT


    B168373
  1. Using a clip remover, remove the 2 clips.

  1. Remove the 3 screws <E>.

  1. Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.



30. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    B168374
  1. Using a clip remover, remove the clip.

  1. Remove the 3 screws <E>.

  1. Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.



31. REMOVE POWER SWITCH


    A170658
  1. Disconnect the switch connector.

  1. Disengage the 2 claws and remove the switch.



32. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B173234
  1. Remove the front door opening trim weatherstrip LH.



33. REMOVE FRONT PILLAR GARNISH LH


    B173222E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 3 guides and remove the front pillar garnish LH.

  1. Remove the clip <A>.



    B173225E01
  1. Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



34. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure for the RH side and the LH side.



35. REMOVE FRONT PILLAR GARNISH RH


    B173682E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 3 guides and remove the front pillar garnish RH.

  1. Remove the clip <A>.



    B173684E01
  1. Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



36. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B168375
  1. Disengage the 2 claws and 2 clips.

  1. Disengage the 2 guides and remove the No. 1 instrument panel speaker panel sub-assembly.



37. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)


    E150560
  1. Remove the 2 bolts and front No. 2 speaker assembly.

  1. Disconnect the connector.



38. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B173014
  1. Disengage the 2 claws and 2 clips.

  1. Disengage the 2 guides and remove the No. 2 instrument panel speaker panel sub-assembly.



39. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT:
Use the same procedures for the RH side and the LH side.



40. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY


    C165103
  1. Disconnect the connector.



41. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
  1. Disconnect each connector.

  1. Remove the 2 passenger airbag bolts <A>.



  1. Disengage each clamp.


    B168376E01

  1. Remove the 2 clips.

  1. Remove the 2 bolts <D> and nut <G>.



  1. Disengage the 5 claws and remove the instrument panel safety pad assembly.


    B168377E02



42. REMOVE NO. 1 HEATER TO REGISTER DUCT


    B168378
  1. Remove the 3 screws <E> and the No. 1 heater to register duct.



43. REMOVE NO. 4 HEATER TO REGISTER DUCT


    B168379
  1. Remove the 3 screws <E> and the No. 4 heater to register duct.



44. REMOVE SIDE NO. 1 DEFROSTER NOZZLE DUCT


    B168380
  1. Remove the screw <E> and the side No. 1 defroster nozzle duct.



45. REMOVE SIDE NO. 2 DEFROSTER NOZZLE DUCT


    B168381
  1. Remove the screw <E> and the side No. 2 defroster nozzle duct.



46. REMOVE DEFROSTER NOZZLE ASSEMBLY


    B173016
  1. Remove the clip.

  1. Remove the 3 screws <E> and the defroster nozzle assembly.



47. REMOVE SOLAR SENSOR
  1. Disconnect the connector.



    E150082
  1. Disengage the 2 claws and remove the solar sensor.