Home › BODY ELECTRICAL › AUDIO / VISUAL › RADIO ANTENNA CORD

RADIO ANTENNA CORD > INSTALLATION

for Preparation Click here



1. INSTALL SATELLITE RADIO ANTENNA ASSEMBLY (w/ Satellite Radio)


    E173851
  1. Engage the 2 claws to install the satellite radio antenna assembly.



    E173850E01
  1. Place the antenna cord in the cutout of the antenna nut.

  1. Install the satellite radio antenna assembly with the antenna nut.

    Torque:
    4.5 N*m{ 46 kgf*cm , 40 in.*lbf }



    E173849
  1. Install the antenna wire to the 3 clamps.



2. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (w/o Satellite Radio)

HINT:
The double-sided tape and tape are not available as supply parts. If they still have enough adhesion to secure the roof headlining and antenna cord, reuse them. If the roof headlining has been replaced with a new one, or if the tape and/or the double-sided tape is no longer sticky, apply new tape following the procedures below.



  1. Apply new double-sided tape.


    E150570E01


    1. Remove the double-sided tape from the roof headlining assembly.

    2. Peel off the appropriate amount of new double-sided tape. Be careful not to touch the adhesive surface.

    3. Apply the double-sided tape to the roof headlining while aligning the tape with the markings on the roof headlining assembly.

    4. Peel off the backing sheet from the double-sided tape.



  1. Install the antenna cord to the roof headlining assembly from the front of the vehicle.


    E150569E01

    HINT:
    For the right front corner of the roof headlining assembly, align the marking tape on the antenna cord with the protrusion of the roof headlining, and wrap tape around the antenna cord and roof headlining assembly once or twice to securely hold them.



3. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (w/ Satellite Radio)

HINT:
The double-sided tape and tape are not available as supply parts. If they still have enough adhesion to secure the roof headlining and antenna cord, reuse them. If the roof headlining has been replaced with a new one, or if the tape and/or the double-sided tape is no longer sticky, apply new tape following the procedures below.



  1. Apply new double-sided tape.


    E150570E02


    1. Remove the double-sided tape from the roof headlining assembly.

    2. Peel off the appropriate amount of new double-sided tape.

      HINT:
      Be careful not to touch the adhesive surface.

      Area
      Dimension
      A
      1.0 mm (0.0394 in.)
      B
      15.0 mm (0.591 in.)

    3. Apply the double-sided tape to the roof headlining while aligning the tape with the markings on the roof headlining assembly.

    4. Peel off the backing sheet from the double-sided tape.



  1. Install the antenna cord to the roof headlining assembly from the front of the vehicle.


    E171647E01

    NOTICE:
    1. Install the antenna cord with the red circle facing up.
    2. Make sure that the antenna cord is not twisted.

    HINT:
    For the right front corner of the roof headlining assembly, align the marking tape on the antenna cord with the protrusion of the roof headlining, and wrap tape around the antenna cord and roof headlining assembly once or twice to securely hold them.



4. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)


    B173274
  1. Pull the roof headlining assembly into the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.

  1. Install the 3 clips.

  1. Connect the sliding roof drive gear connector.

  1. Connect the No. 2 antenna cord sub-assembly connector to the rear pillar RH.

  1. Connect the No. 2 antenna cord sub-assembly connector and engage the 3 clamps to the front pillar RH.

  1. Install the No. 2 antenna cord sub-assembly to the front pillar RH with the bolt.

  1. w/ Rear Seat Entertainment System:

    1. Connect the No. 1 roof wire connector to the rear pillar LH.



  1. Connect the No. 1 roof wire connectors and engage the 3 clamps to the front pillar LH.


    B209456E01

    NOTICE:
    After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.



5. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)


    B173271
  1. Pull the roof headlining assembly into the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.

  1. Install the 4 clips.

  1. Connect the No. 2 antenna cord sub-assembly connector to the rear pillar RH.

  1. Connect the No. 2 antenna cord sub-assembly connectors and engage the 3 clamps to the front pillar RH.

  1. Install the No. 2 antenna cord sub-assembly to the front pillar RH with the bolt.



  1. Connect the No. 1 roof wire connector and engage the 3 clamps to the front pillar LH.


    B209455E01

    NOTICE:
    After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.



6. INSTALL VISOR HOLDER


    B151383
  1. Engage the 2 claws.

  1. Push in the visor holder as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and the LH side.



7. INSTALL SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)


    B175148E01
  1. Align the joining point of the moulding with the notch of the roof headlining assembly, and install the sun roof opening trim moulding.

    NOTICE:
    After installation, check that the corners fit correctly.



8. INSTALL ROOF HEADLINING TRIM CLIP STOPPER


    B173594
  1. Install the roof headlining trim clip stopper with the bolt.

  1. Engage the 3 claws.

    HINT:
    Use the same procedure for the RH side and the LH side.



9. INSTALL ASSIST GRIP ASSEMBLY (w/ Sliding Roof)


    B173259
  1. Assemble the assist grip assembly as shown in the illustration.



    B173260
  1. Install the assist grip assembly.

    HINT:
    Use the same procedure for the other 4 assist grips.



10. INSTALL REAR ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)


    B131970
  1. Assemble the rear assist grip sub-assembly as shown in the illustration.



    B167237
  1. Install the rear assist grip sub-assembly.

    HINT:
    Use the same procedure for the RH side and the LH side.



11. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)


    B125984
  1. Assemble the front assist grip sub-assembly as shown in the illustration.



    B160427
  1. Install the front assist grip sub-assembly.

    HINT:
    Use the same procedure for the RH side and the LH side.



12. INSTALL TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)


    E151790
  1. Engage the 2 claws and the 2 clips.



    E150582
  1. Install the television display with the 4 bolts.

  1. Connect the connector.



13. INSTALL TELEVISION BASE (w/ Rear Seat Entertainment System)


    E150581E01
  1. Engage the 2 guides and 4 clips and install the television base.



14. INSTALL NO. 2 ROOM LIGHT ASSEMBLY


    B139564
  1. Engage the 4 claws and install the lens cover.



    B139562
  1. Engage the 4 claws and install the room light switch base to the No. 2 room light assembly.



    B160475
  1. Engage the 4 claws and install the No. 2 room light assembly.



15. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (for Standard)


    B139564
  1. Engage the 4 claws and install the lens cover.



    B139562
  1. Engage the 4 claws and install the room light switch base to the No. 1 room light assembly.



    B160475
  1. Engage the 4 claws and install the No. 1 room light assembly.



16. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (for Independent Type)


    B173253
  1. Engage the 4 claws and install the lens cover.



    B173256
  1. Engage the 8 claws and install the room light switch base to the No. 1 room light assembly.



    B173255
  1. Engage the 4 claws and install the No. 1 room light assembly.



17. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    B175049
  1. Engage the 2 claws and install the inner rear view mirror stay holder cover.



    B175050E01
  1. Engage the 2 claws and install the inner rear view mirror stay holder cover as shown in the illustration.



18. INSTALL VISOR ASSEMBLY LH


    B173261
  1. Install the visor assembly LH with the 2 screws.



19. INSTALL VISOR BRACKET COVER (for LH Side)


    B139566
  1. Engage the 4 claws and install the visor bracket cover.



20. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



21. INSTALL VISOR BRACKET COVER (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.



22. INSTALL ROOF CONSOLE BOX ASSEMBLY


    B173251
  1. Connect the connector.

  1. Engage the 3 guides, 2 clips, fastener, and install the roof console box assembly.



23. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (w/ Power Back Door)


  1. w/ Rear No. 2 Seat:



      B173265
    1. Engage the 2 guides and 5 clips.

    2. Install the roof side inner garnish assembly LH with the bolt.



    3. B175157
    4. Engage the 2 guides and the 2 claws, and install the No. 2 seat outer belt guide.



  1. w/o Rear No. 2 Seat:



      B173266
    1. Engage the 2 guides and 5 clips.

    2. Install the roof side inner garnish assembly LH with the bolt.



24. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (w/o Power Back Door)


  1. w/ Rear No. 2 Seat:



      B173267
    1. Engage the 2 guides and 5 clips.

    2. Install the roof side inner garnish assembly LH with the bolt.



    3. B175157
    4. Engage the 2 guides and the 2 claws, and install the No. 2 seat outer belt guide.



  1. w/o Rear No. 2 Seat:



      B173268
    1. Engage the 2 guides and 5 clips.

    2. Install the roof side inner garnish assembly LH with the bolt.



25. INSTALL QUARTER PILLAR GARNISH LH


    B173264
  1. Engage the 2 guides and the 2 clips, and install the quarter pillar garnish LH as shown in the illustration.



    B175156
  1. Engage the 2 guides and the 2 claws, and install the No. 1 seat outer belt guide.



26. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.



  1. Install the deck trim side panel assembly LH with the 2 bolts.


    B173613



27. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH


    B170934E01
  1. Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.



28. INSTALL FRONT DECK SIDE TRIM COVER LH


    B175145
  1. Engage the 4 claws and install the 2 front deck side trim covers LH.



29. INSTALL NO. 2 DECK SIDE TRIM HOOK


    B173612
  1. Install the No. 2 deck side trim hook with the screw.



30. INSTALL ROPE HOOK ASSEMBLY (for LH Side)


    B173599
  1. for Front Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.



    B173601
  1. for Rear Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.



31. INSTALL REAR DECK TRIM COVER (w/o Remote Folding Function)


    B173602
  1. Engage the 10 claws and install the rear deck trim cover.



32. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)


    B173603
  1. Engage the 5 claws and install the reclining remote control bezel lever LH.



33. INSTALL REAR POWER OUTLET SOCKET COVER


    E151328
  1. Engage the 2 claws and install the rear power outlet socket cover.



34. INSTALL REAR POWER POINT SOCKET ASSEMBLY


    E151490
  1. Engage the claw and install the rear power point socket assembly.

  1. Connect the connector.



35. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH


    B175146
  1. Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.



36. INSTALL SIDE TRIM COVER LH (w/o Rear Seat Entertainment System)


    B173597
  1. Engage the 10 claws and install the side trim cover LH.



37. INSTALL POWER OUTLET SOCKET BEZEL (w/ Rear Seat Entertainment System)


    B173681
  1. Connect each connector.



    B173680
  1. Engage the 4 claws and install the power outlet socket bezel.



38. INSTALL DECK SIDE TRIM LH


    B173624
  1. Engage the 3 guides and 4 claws as shown in the illustration.



    B173596
  1. Install the deck side trim LH with the bolt.



39. INSTALL DECK SIDE TRIM COVER LH


    B175144
  1. Engage the 2 claws and install the deck side trim cover LH.



40. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and the LH side.



41. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH (w/o Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and the LH side.



42. INSTALL QUARTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.



43. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.



  1. Install the deck trim side panel assembly RH with the 3 bolts.


    B173622



44. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



45. INSTALL FRONT DECK SIDE TRIM COVER RH

HINT:
Use the same procedure for the RH side and the LH side.



46. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

HINT:
Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.



47. INSTALL ROPE HOOK ASSEMBLY (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.



48. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH


    B173619
  1. Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.



49. INSTALL REAR ROOM TEMPERATURE SENSOR (w/ Rear Automatic Air Conditioning System)
  1. Connect the connector.



    E150364
  1. Engage the 4 claws and install the rear room temperature sensor.



50. INSTALL SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)


    B173610
  1. Engage the 4 claws, and install the side trim cover RH.



51. INSTALL DECK SIDE TRIM RH

HINT:
Use the same procedure for the RH side and the LH side.



52. INSTALL DECK SIDE TRIM COVER RH

HINT:
Use the same procedure for the RH side and the LH side.



53. INSTALL REAR SEAT SIDE GARNISH CAP (w/ Rear Air Conditioning System)


    B173617
  1. Engage the guide and the 6 claws.

  1. Install the rear seat side garnish cap with the screw.



54. INSTALL REAR SEAT SIDE GARNISH CAP (w/o Rear Air Conditioning System)


    B173615
  1. Engage the guide and the 8 claws, and install the rear seat side garnish cap.



55. INSTALL REAR FLOOR FINISH PLATE


    B173609
  1. Engage the 4 clips and the 4 claws, and install the rear floor finish plate.



56. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    B173781
  1. Install the rear No. 2 seat assembly with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



57. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)


    B170936
  1. Install the rear seat lap type belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.



58. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)
  1. Install the rear seat lap type belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.



59. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)


    B170935
  1. Install the rear No. 2 seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

    HINT:
    Use the same procedure for the RH side and LH side.



60. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    B173679
  1. Install the rear deck floor box with the 2 nuts.



61. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)


    B178560
  1. Install the deck floor board assembly with the 4 nuts and 4 bolts.



62. INSTALL REAR MAT


    B173249
  1. Install the rear mat.



63. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)


    B178561
  1. Install the 2 nuts and the deck floor board assembly.

  1. Engage the 3 claws.



64. INSTALL DECK SIDE TRIM BOX LH


  1. Install the deck side trim box LH as shown in the illustration.


    B178555



    B173243E01
  1. Install the 2 deck side trim clip and the clips.



65. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)


    B173607
  1. Engage the 2 clips and install the rear seat side cover LH.



66. INSTALL DECK SIDE TRIM BOX RH


  1. Install the deck side trim box RH as shown in the illustration.


    B178553



    B173247E01
  1. Install the 2 deck side trim clip and the clips.



67. INSTALL JACK CARRIER ASSEMBLY


    B178549
  1. Engage the 3 claws, and install the jack carrier assembly.



68. INSTALL JACK ASSEMBLY


    B173245
  1. Install the jack assembly.



69. INSTALL JACK CARRIER CUSHION


    B178550
  1. Install the jack carrier cushion.



70. INSTALL JACK CARRIER SUPPORT


71. INSTALL REAR SEAT SIDE COVER RH (w/ Rear Air Conditioning System)


    B173608
  1. Engage the 2 clips and install the rear seat side cover RH.



72. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear Air Conditioning System)


    B175152
  1. Engage the 3 guides and 3 clips and install the rear No. 1 floor board.



73. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover assembly.



74. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    B173244
  1. Engage the 2 guides and install the No. 2 deck board sub-assembly.



75. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    B173242
  1. Engage the 2 guides and install the No. 3 deck board sub-assembly.



76. INSTALL DECK BOARD ASSEMBLY


    B173240
  1. Install the deck board assembly.



77. INSTALL CENTER PILLAR GARNISH LH


    B173229
  1. Engage the 2 guides and the clip.

  1. Install the center pillar garnish LH with the clip and screw.



78. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    B170910
  1. Install the floor end of the front seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.



79. INSTALL LOWER CENTER PILLAR GARNISH LH


    B173231
  1. Engage the 2 claws and the 2 clips, and install the lower center pillar garnish LH.



80. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B173233E01
  1. Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

    NOTICE:
    After installation, check that the corners fit correctly.



81. INSTALL REAR DOOR SCUFF PLATE LH


    B173228
  1. Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.



82. INSTALL CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.



83. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



84. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.



85. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B173237E01
  1. Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

    NOTICE:
    After installation, check that the corners fit correctly.



86. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.



87. INSTALL REAR NO. 1 SEAT ASSEMBLY LH


    B173778
  1. Temporarily install the 2 bolts on the front side of the seat.



    B173780
  1. Temporarily install the 3 bolts on the rear side of the seat.

  1. Install the rear No. 1 seat assembly with the 5 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



88. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)


  1. Remove the rear seat reclining control cable from the carpet hole.


    B180395E01

  1. Connect the rear seat reclining control cable as shown in the illustration.



  1. Connect the rear No. 1 seat lock cable assembly as shown in the illustration.


    B173771E01



    B174591
  1. Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Return the seatback to the upright position.



  1. Pull up the adjuster's lock piece to lock it as shown in the illustration.


    B180389E01

    NOTICE:
    When pressing the lock piece, make sure the adjuster's spring is not compress.



89. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for LH Side)
  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.



90. INSTALL REAR SEAT LEG SIDE COVER LH


    B181544
  1. Engage the 3 claws and install the rear seat leg side cover.



91. INSTALL RECLINING HINGE COVER LH


    B181543
  1. Engage the 2 clips and install the reclining hinge cover LH.



92. INSTALL REAR INNER TRACK BRACKET COVER LH


    B181542
  1. Engage the 5 claws and install the rear inner track bracket cover.



93. INSTALL REAR OUTER TRACK BRACKET COVER LH


    B173776
  1. Engage the 4 claws and install the rear outer track bracket cover.



94. INSTALL REAR SEAT TRACK BRACKET COVER LH


    B173775
  1. Engage the 8 claws and install the 2 rear seat track bracket covers.



95. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)


    B176351
  1. Install the rear seat headrest assembly as shown in the illustration.



96. INSTALL REAR CENTER SEAT ASSEMBLY


97. INSTALL REAR NO. 1 SEAT ASSEMBLY RH


    B173764
  1. Temporarily install the 2 bolts on the front side of the seat.



    B173774
  1. Temporarily install the 3 bolts on the rear side of the seat.

  1. Install the rear No. 1 seat assembly with the 5 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



98. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)


  1. Remove the rear seat reclining control cable from the carpet hole.


    B180394E01

  1. Connect the rear seat reclining control cable as shown in the illustration.



  1. Connect the rear No. 1 seat lock cable assembly as shown in the illustration.


    B173769E01



    B173767
  1. Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Return the seatback to the upright position.



  1. Pull up the adjuster's lock piece to lock it as shown in the illustration.


    B180391E01

    NOTICE:
    When pressing the lock piece, make sure the adjuster's spring is not compress.



99. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for RH Side)
  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.



100. INSTALL REAR SEAT LEG SIDE COVER RH


    B173765
  1. Engage the clip.

  1. Engage the 3 claws and install the rear seat leg side cover.



101. INSTALL REAR INNER TRACK BRACKET COVER RH


    B181546
  1. Engage the 5 claws and install the rear inner track bracket cover.



102. INSTALL REAR OUTER TRACK BRACKET COVER RH


    B173763
  1. Engage the 4 claws and install the rear outer track bracket cover.



103. INSTALL REAR SEAT TRACK BRACKET COVER RH


    B173760
  1. Engage the 8 claws and install the 2 seat track bracket covers.



104. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)


    B176352
  1. Install the rear seat headrest assembly as shown in the illustration.



105. INSTALL ANTENNA CORD SUB-ASSEMBLY


  1. Engage the 9 clamps and install the antenna cord sub-assembly.


    E150564



106. INSTALL NAVIGATION ANTENNA ASSEMBLY (w/ Navigation System)


    E150590
  1. Install the navigation antenna with the 2 screws.



    E150591
  1. Engage the 3 clamps and install the navigation antenna assembly.



107. INSTALL CENTER HEATER TO REGISTER SUB DUCT


    B168382
  1. Install the center heater to register sub duct with the 2 screws <E>.



108. INSTALL DEFROSTER NOZZLE ASSEMBLY


    B173016
  1. Install the defroster nozzle assembly with the 3 screws <E> and clip.



109. INSTALL SIDE NO. 2 DEFROSTER NOZZLE DUCT


    B168381
  1. Install the side No. 2 defroster nozzle duct with the screw <E>.



110. INSTALL SIDE NO. 1 DEFROSTER NOZZLE DUCT


    B168380
  1. Install the side No. 1 defroster nozzle duct with the screw <E>.



111. INSTALL NO. 4 HEATER TO REGISTER DUCT


    B168379
  1. Install the No. 4 heater to register duct with the 3 screws <E>.



112. INSTALL NO. 1 HEATER TO REGISTER DUCT


    B168378
  1. Install the No. 1 heater to register duct with the 3 screws <E>.



113. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY
  1. Engage the 5 claws.

    NOTICE:
    Do not allow the wire harness to get caught in the claws.

  1. Install the 2 bolts <D> and nut <G>.



  1. Install the 2 clips.


    B168377E02

  1. Engage each clamp.

  1. Install the 2 passenger airbag bolts <A>.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



  1. Connect each connector and install the instrument panel safety pad assembly.


    B168376E01



114. CONNECT INSTRUMENT PANEL WIRE ASSEMBLY
  1. Check that the power switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.



    C165103
  1. Connect the connector.



115. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)
  1. Connect the connector.



    E150560
  1. Install the front No. 2 speaker assembly with the 2 bolts.



116. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B168375
  1. Engage the 2 guides.

  1. Engage the 2 claws and 2 clips, and install the No. 1 instrument panel speaker panel sub-assembly.



117. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.



118. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B173014
  1. Engage the 2 guides.

  1. Engage the 2 claws and 2 clips, and install the No. 2 instrument panel speaker panel sub-assembly.



119. INSTALL FRONT PILLAR GARNISH LH


    B173226E01
  1. Remove the protective cover.



    B173223E01
  1. Install a new clip <A> on the front pillar garnish LH.

  1. Engage the 3 guides and 2 clips, then install the front pillar garnish LH.



120. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B173235E01
  1. Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

    NOTICE:
    After installation, check that the corners fit correctly.



121. INSTALL FRONT PILLAR GARNISH RH


    B173685E01
  1. Remove the protective cover.



    B173683E01
  1. Install a new clip <A> on the front pillar garnish RH.

  1. Engage the 3 guides and 2 clips, then install the front pillar garnish RH.



122. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B173239E01
  1. Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

    NOTICE:
    After installation, check that the corners fit correctly.



123. INSTALL POWER SWITCH


    A170658
  1. Engage the 2 claws to install the switch.

  1. Connect the switch connector.



124. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    B168374
  1. Engage the claw and 2 guides.

  1. Install the front No. 2 console box insert with the 3 screws <E> and clip.



125. INSTALL FRONT NO. 1 CONSOLE BOX INSERT


    B168373
  1. Engage the claw and 2 guides.

  1. Install the front No. 1 console box insert with the 3 screws <E> and 2 clips.



126. INSTALL CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)


    B173629
  1. Engage the 6 claws.



    B173628
  1. Install the console box assembly with the 4 bolts and 2 screws.



127. INSTALL CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)


    B175149
  1. Engage the 6 claws.

  1. Connect the connector.



    B181135
  1. Install the console box assembly with the 4 bolts and 2 screws.



128. INSTALL LOWER REAR CONSOLE BOX
  1. Install the lower rear console box.



129. INSTALL NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)


    B173013
  1. Install the No. 2 console box duct as shown in the illustration.



130. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    B168372
  1. Connect the connector.

  1. Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.



131. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Connect each connector and clamp.



    B168370
  1. Engage the 4 claws and 3 clips.

  1. Install the lower instrument panel sub-assembly with the 2 bolts <B> and 3 screws <E>.



132. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B173000
  1. Engage the 2 guides.

  1. Engage the 3 claws and install the No. 2 instrument panel under cover sub-assembly.



133. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    B173009
  1. Connect the hood lock control cable assembly.

  1. Connect each connector and the aspirator duct.



    B173021
  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.



134. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    B173227
  1. Engage the claw and clip, install the cowl side trim sub-assembly LH.

  1. Install the clip.



135. INSTALL FRONT DOOR SCUFF PLATE LH


    B173224
  1. Engage the guide and the 8 claws, and install the front door scuff plate LH.



136. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



137. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.



138. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)
  1. Connect each connector.



    E150552
  1. Engage the 4 clips.



    E150551
  1. Install the radio receiver assembly with bracket with the 4 bolts.



139. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)
  1. Connect each connector.



    E150545
  1. Engage the 4 clips.



    E150544
  1. Install the navigation receiver assembly with bracket with the 4 bolts.



140. INSTALL HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)
  1. Connect the connector.



    E150368
  1. Engage the 4 clips and install the heater control and accessory assembly.



141. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)
  1. Connect the connector.



    E150367
  1. Engage the 4 clips and install the air conditioning control assembly.



142. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B184681E01
  1. Apply protective tape to the areas shown in the illustration.

  1. Connect each connector.

  1. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

    NOTICE:
    Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.



143. INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    B168369
  1. Engage the 2 claws and 5 clips, and install the center instrument panel register assembly.



144. INSTALL COMBINATION METER ASSEMBLY
  1. Connect the connector.



    E152487
  1. Install the combination meter assembly with the 4 screws.



145. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    E152488
  1. Engage the 4 claws and 4 clips, and install the instrument cluster finish panel assembly.



146. POSITION FRONT WHEELS STRAIGHT AHEAD


147. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    C166129
  1. Using pliers, engage the claw. Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.

  1. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.



148. INSTALL STEERING COLUMN COVER


    C165716
  1. Engage the claw to install the upper steering column cover.



    C166128
  1. Engage the 2 claws to install the lower steering column cover.



    C165715
  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



149. ADJUST SPIRAL CABLE SUB-ASSEMBLY
  1. Check that the power switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.



    C165096
  1. Rotate the spiral cable counterclockwise slowly by hand until it stops.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.



    C165097E01
  1. Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.

    HINT:
    The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.



150. INSTALL STEERING WHEEL ASSEMBLY


    C165708E01
  1. Align the matchmarks on the steering wheel assembly and steering main shaft.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connectors to the spiral cable sub-assembly.



151. INSPECT STEERING WHEEL CENTER POINT


152. INSTALL STEERING PAD
  1. Check that the power switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.



    C165092
  1. Support the steering pad with one hand as shown in the illustration.



    C165093
  1. Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector to the steering pad.

  1. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.



    C166982E01
  1. Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



153. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    C178264
  1. Install the lower No. 2 steering wheel cover with the claw.



154. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    C165090
  1. Install the lower No. 3 steering wheel cover with the claw.



155. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



156. INSPECT STEERING PAD


    C166979
  1. With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:

    1. Cuts, minute cracks or marked discoloration on the steering pad top surface or grooves.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system (Click here).



157. INSPECT SRS WARNING LIGHT
(Click here)