POWER WINDOW REGULATOR MOTOR > INSTALLATION |
| 1. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Door) |
![]() |
Using a "TORX" driver (T25), install the front power window regulator motor sub-assembly with the 3 screws.
| 2. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (for Front Door) |
Apply MP grease to the sliding parts of the front door window regulator sub-assembly.
![]() |
Install the temporary bolt to the front door window regulator sub-assembly.
Temporarily install the window regulator.
Tighten the 6 bolts in the order shown in the illustration to install the front window regulator.
| 3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY (for Front Door) |
![]() |
Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated in the order of the arrows in the illustration.
![]() |
Install the front door glass sub-assembly with the 2 bolts.
![]() |
Install the hole plug.
| 4. INSTALL FRONT DOOR SERVICE HOLE COVER (for Front Door) |
Apply butyl tape to the front door panel.
Pass the front door lock remote control cable and rear door inside the locking cable through a new front door service hole cover.
![]() |
Attach the front door service hole cover according to the reference points on the front door panel.
![]() |
Connect each connector.
Engage the 2 clamps.
| 5. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP (for Front Door) |
![]() |
Install the front door inner glass weatherstrip.
| 6. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for Front Door) |
Connect the connector.
![]() |
Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.
Engage the 2 clamps.
![]() |
Engage the front door trim board with the 5 claws on the front door inner glass weatherstrip.
Engage the 9 clips.
![]() |
Install the 2 screws <B>.
Install the screw <A> and front door trim board to the front door panel.
| 7. INSTALL COURTESY LIGHT ASSEMBLY (for Front Door) |
Connect the connector.
![]() |
Engage the claw and install the courtesy light assembly.
| 8. INSTALL ASSIST GRIP COVER (for Front Door) |
![]() |
Engage the 4 claws and install the assist grip cover.
| 9. INSTALL FRONT ARMREST UPPER BASE PANEL (for Front Door) |
Connect the connector.
![]() |
Engage the 7 claws and clip and install the front armrest upper base panel.
| 10. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG (for Front Door) |
![]() |
Engage the 3 claws and install the front door inside handle bezel plug.
| 11. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH (for Front Door) |
![]() |
Engage the clip and claw, and install the front door lower frame bracket garnish.
| 12. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear Door) |
![]() |
Using a "TORX" driver (T25), install the rear power window regulator motor assembly with the 3 screws.
![]() |
Connect a positive (+) lead of the battery to terminal 1, and a negative (-) lead to terminal 2 of the rear power window regulator motor assembly to move the lift arm to the position shown in the illustration.
| 13. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (for Rear Door) |
Apply MP grease to the sliding parts of the rear door window regulator sub-assembly.
![]() |
Install the temporary bolt to the rear door window regulator sub-assembly.
Temporarily install the window regulator.
Tighten the 4 bolts in the order shown in the illustration to install the rear door window regulator.
Connect the connector.
| 14. INSTALL REAR DOOR GLASS SUB-ASSEMBLY (for Rear Door) |
![]() |
Slide the rear door glass sub-assembly to install it as shown in the illustration.
| 15. INSTALL REAR DOOR QUARTER WINDOW GLASS (for Rear Door) |
Install the rear door quarter window glass to the rear door quarter window weatherstrip.
![]() |
Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.
| 16. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY (for Rear Door) |
Insert the rear door window division bar sub-assembly from above.
Install the rear door glass run to the rear door lower window frame sub-assembly.
![]() |
Install the rear door window division bar sub-assembly with the 2 bolts and screw.
![]() |
Install the rear door vent seal.
| 17. INSTALL REAR DOOR GLASS RUN (for Rear Door) |
![]() |
Install the rear door glass run.
| 18. INSTALL REAR DOOR WEATHERSTRIP (for Rear Door) |
Install the front door weatherstrip.
| 19. INSTALL REAR DOOR SERVICE HOLE COVER (for Rear Door) |
Apply butyl tape to the rear door panel.
![]() |
Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.
Attach the rear door service hole cover according to the reference points on the rear door panel.
Connect the connector.
| 20. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP (for Rear Door) |
![]() |
Install the rear door inner glass weatherstrip.
| 21. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY (for Rear Door) |
![]() |
Connect the rear door lock remote control cable and rear door inside locking cable to the rear door inside handle sub-assembly.
Engage the 2 clamps.
![]() |
Engage the rear door trim board with the 5 claws on the rear door inner glass weatherstrip.
Engage the 9 clips and install the rear door trim board to the rear door panel.
![]() |
Install the 2 screws <B>.
Install the screw <A>.
| 22. INSTALL DOOR ASSIST GRIP COVER (for Rear Door) |
![]() |
Engage the 4 claws and install the door assist grip cover.
| 23. INSTALL REAR DOOR ARMREST UPPER BASE PANEL (for Rear Door) |
Connect the connector.
![]() |
Engage the 6 claws and 2 clips and install the rear door armrest upper base panel.
| 24. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG (for Rear Door) |
![]() |
Engage the 3 claws to install the rear door inside handle bezel plug.
| 25. CONNECT NEGATIVE BATTERY TERMINAL |
| 26. INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side) |