FRONT DOOR BLACK OUT TAPE > INSTALLATION |
| 1. REPAIR INSTRUCTION |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Wipe off any tape adhesive residue with cleaner.
Installation temperature
When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.
Before installation
Remove any roughness of coating and dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.
Key points for handling the tape
The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.
Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)
To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (for pressing forward) or 30 to 45° (for pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf) at a constant slow speed of 3 to 7 cm (1.2 to 2.8 in.) per second.

Key points for installation of the tape (how to use a squeegee and installation procedure for hemming surfaces)
![]() |
If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.
Key points for installation of the tape (how to use a squeegee and installation procedure for corners)
Remove the release paper and apply the tape carefully with your fingers.
Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.
Check after installation
After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.
| 2. INSTALL INNER REAR BLACK OUT FRONT DOOR TAPE |
![]() |
Referring to the illustration, position the inner rear black out front door tape.
Remove the release paper and apply the tape.
| 3. INSTALL INNER UPPER BLACK OUT FRONT DOOR TAPE |
![]() |
Referring to the illustration, position the inner upper black out front door tape.
Remove the release paper and apply the tape.
| 4. INSTALL NO. 1 BLACK OUT TAPE |
![]() |
Referring to the illustration, position the No. 1 black out tape.
| Dimension | Measurement |
| A | 2 to 4 mm (0.079 to 0.157 in.) |
| B | 4 to 6 mm (0.157 to 0.236 in.) |
Remove the release paper and apply the tape.
| 5. INSTALL FRONT DOOR WEATHERSTRIP |
![]() |
Install the front door weatherstrip.
| 6. INSTALL DOOR FRAME GARNISH |
![]() |
Engage a new clip and install the door frame garnish.
| 7. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY |
![]() |
Engage the 6 claws and install the front door belt moulding assembly.
| 8. INSTALL FRONT DOOR GLASS RUN |
![]() |
Install the front door glass run.
| 9. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY |
Apply MP grease to the sliding parts of the front door window regulator sub-assembly.
![]() |
Install the temporary bolt to the front door window regulator sub-assembly.
Temporarily install the window regulator.
Tighten the 6 bolts in the order shown in the illustration to install the front window regulator.
| 10. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY |
![]() |
Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated in the order of the arrows in the illustration.
![]() |
Install the front door glass sub-assembly with the 2 bolts.
![]() |
Install the hole plug.
| 11. INSTALL FRONT DOOR SERVICE HOLE COVER |
Apply butyl tape to the front door panel.
Pass the front door lock remote control cable and rear door inside the locking cable through a new front door service hole cover.
![]() |
Attach the front door service hole cover according to the reference points on the front door panel.
![]() |
Connect each connector.
Engage the 2 clamps.
| 12. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER |
![]() |
Engage the claw, and temporarily install the outer rear view mirror assembly with cover.
Tighten the 3 nuts in the order shown in the illustration to install the outer rear view mirror assembly with cover.
![]() |
Engage the clamp and connect the connector.
Install the clip.
| 13. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY |
![]() |
Install the front No. 1 speaker assembly with the 4 bolts.
Connect the connector.
| 14. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP |
![]() |
Install the front door inner glass weatherstrip.
| 15. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
Connect the connector.
![]() |
Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.
Engage the 2 clamps.
![]() |
Engage the front door trim board with the 5 claws on the front door inner glass weatherstrip.
Engage the 9 clips.
![]() |
Install the 2 screws <B>.
Install the screw <A> and front door trim board to the front door panel.
| 16. INSTALL COURTESY LIGHT ASSEMBLY |
Connect the connector.
![]() |
Engage the claw and install the courtesy light assembly.
| 17. INSTALL ASSIST GRIP COVER |
![]() |
Engage the 4 claws and install the assist grip cover.
| 18. INSTALL FRONT ARMREST UPPER BASE PANEL |
Connect the connector.
![]() |
Engage the 7 claws and clip and install the front armrest upper base panel.
| 19. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Engage the 3 claws and install the front door inside handle bezel plug.
| 20. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH |
![]() |
Engage the clip and claw, and install the front door lower frame bracket garnish.
| 21. CONNECT NEGATIVE BATTERY TERMINAL |
| 22. INITIALIZE WINDOW CONTROL SYSTEM (for Driver Side) |