REAR DOOR BLACK OUT TAPE > INSTALLATION |
| 1. REPAIR INSTRUCTION |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Wipe off any tape adhesive residue with cleaner.
Installation temperature
When ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.
Before installation
Remove any roughness of coating and dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.
Key points for handling the tape
The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.
Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)
To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (for pressing forward) or 30 to 45° (for pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf) at a constant slow speed of 3 to 7 cm (1.2 to 2.8 in.) per second.

Key points for installation of the tape (how to use a squeegee and installation procedure for hemming surfaces)
![]() |
If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.
Key points for installation of the tape (how to use a squeegee and installation procedure for corners)
Remove the release paper and apply the tape carefully with your fingers.
Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.
Check after installation
After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.
| 2. INSTALL INNER REAR BLACK OUT REAR DOOR TAPE |
![]() |
Referring to the illustration, position the inner rear black out rear door tape.
Remove the release paper and apply the tape.
| 3. INSTALL INNER FRONT BLACK OUT REAR DOOR TAPE |
![]() |
Referring to the illustration, position the inner front black out rear door tape.
Remove the release paper and apply the tape.
| 4. INSTALL INNER UPPER BLACK OUT REAR DOOR TAPE |
![]() |
Referring to the illustration, position the inner upper black out rear door tape.
Remove the release paper and apply the tape.
| 5. INSTALL NO. 2 BLACK OUT TAPE |
![]() |
Referring to the illustration, position the No. 2 black out tape.
| Dimension | Measurement |
| A | 2 to 4 mm (0.079 to 0.157 in.) |
| B | 4 to 6 mm (0.157 to 0.236 in.) |
Remove the release paper and apply the tape.
| 6. INSTALL NO. 3 BLACK OUT TAPE |
![]() |
Referring to the illustration, position the No. 3 black out tape.
| Dimension | Measurement |
| A | 2 to 4 mm (0.079 to 0.157 in.) |
| B | 4 to 6 mm (0.157 to 0.236 in.) |
Remove the release paper and apply the tape.
| 7. INSTALL REAR DOOR WEATHERSTRIP |
![]() |
Install the rear door weatherstrip.
| 8. INSTALL REAR DOOR FRAME GARNISH |
![]() |
Engage a new clip and install the rear door frame garnish.
| 9. INSTALL REAR DOOR BELT MOULDING ASSEMBLY |
![]() |
Engage the 6 claws and install the rear door belt moulding assembly.
| 10. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY |
Apply MP grease to the sliding parts of the rear door window regulator sub-assembly.
![]() |
Install the temporary bolt to the rear door window regulator sub-assembly.
Temporarily install the window regulator.
Tighten the 4 bolts in the order shown in the illustration to install the rear door window regulator.
Connect the connector.
| 11. INSTALL REAR DOOR GLASS RUN |
![]() |
Install the rear door glass run.
| 12. INSTALL REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Slide the rear door glass sub-assembly to install it as shown in the illustration.
| 13. INSTALL REAR DOOR QUARTER WINDOW GLASS |
Install the rear door quarter window glass to the rear door quarter window weatherstrip.
![]() |
Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.
| 14. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY |
Insert the rear door window division bar sub-assembly from above.
Install the rear door glass run to the rear door lower window frame sub-assembly.
![]() |
Install the rear door window division bar sub-assembly with the 2 bolts and screw.
![]() |
Install the rear door vent seal.
| 15. INSTALL REAR DOOR SERVICE HOLE COVER |
Apply butyl tape to the rear door panel.
![]() |
Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.
Attach the rear door service hole cover according to the reference points on the rear door panel.
Connect the connector.
| 16. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP |
![]() |
Install the rear door inner glass weatherstrip.
| 17. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Connect the rear door lock remote control cable and rear door inside locking cable to the rear door inside handle sub-assembly.
Engage the 2 clamps.
![]() |
Engage the rear door trim board with the 5 claws on the rear door inner glass weatherstrip.
Engage the 9 clips and install the rear door trim board to the rear door panel.
![]() |
Install the 2 screws <B>.
Install the screw <A>.
| 18. INSTALL DOOR ASSIST GRIP COVER |
![]() |
Engage the 4 claws and install the door assist grip cover.
| 19. INSTALL REAR DOOR ARMREST UPPER BASE PANEL |
Connect the connector.
![]() |
Engage the 6 claws and 2 clips and install the rear door armrest upper base panel.
| 20. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Engage the 3 claws to install the rear door inside handle bezel plug.
| 21. CONNECT NEGATIVE BATTERY TERMINAL |