Home › BODY › EXTERIOR › REAR DOOR BLACK OUT TAPE

REAR DOOR BLACK OUT TAPE > REMOVAL

for Preparation Click here



1. DISCONNECT NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the terminal to prevent airbag deployment (Click here).

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    B172920E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.



3. REMOVE REAR DOOR ARMREST UPPER BASE PANEL


    B172987E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and 2 clips, and remove the rear door armrest upper base panel.

  1. Disconnect the connector.



4. REMOVE DOOR ASSIST GRIP COVER


    B174184E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws and remove the door assist grip cover.



5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B173155
  1. Remove the 3 screws.



    B173156
  1. Using a clip remover, disengage the 9 clips.

  1. Disengage the 5 claws and separate the rear door trim board sub-assembly from the rear door inner glass weatherstrip.



    B173157
  1. Disengage the 2 clamps.

  1. Disconnect the front door lock remote control cable and rear door inside locking cable.



6. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    B173160
  1. Remove the rear door inner glass weatherstrip from the rear door panel.



7. REMOVE REAR DOOR SERVICE HOLE COVER


    B173161
  1. Disconnect the connector.

  1. Remove the rear door service hole cover.

    HINT:
    Remove the remaining tape on the door.



8. REMOVE REAR DOOR GLASS RUN


    B173165
  1. Remove the rear door glass run.



9. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    B173164
  1. Remove the rear door vent seal.



    B173167
  1. Remove the 2 bolts, screw, and the rear door window division bar sub-assembly.



10. REMOVE REAR DOOR QUARTER WINDOW GLASS


    B173168
  1. Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.

  1. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.



11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    B173170
  1. Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.



12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


    B173172E01
  1. Disconnect the connector.

  1. Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.

  1. Remove the 3 bolts.

  1. Remove the rear door window regulator sub-assembly and the rear power window regulator motor assembly as a unit.

  1. Remove the temporary bolt from the rear door window regulator sub-assembly.



13. REMOVE REAR DOOR BELT MOULDING ASSEMBLY


    B172793E01
  1. Put protective tape around the rear door belt moulding assembly.



    B172794
  1. Disengage the 6 claws and remove the rear door belt moulding assembly.

    NOTICE:
    Be careful when removing the moulding as there are claws attached to the front end of the moulding.



14. REMOVE REAR DOOR FRAME GARNISH


    B173166
  1. Disengage the clip and remove the rear door frame garnish.

    HINT:
    This clip needs to be replaced with a new one because the clip will break when removing the rear door frame garnish.



15. REMOVE REAR DOOR WEATHERSTRIP


    B174415
  1. Remove the upper part of the rear door weatherstrip to the extent that allows removal of the black out tape.



16. REMOVE NO. 3 BLACK OUT TAPE
  1. Using a heat light, heat the No. 3 black out tape and vehicle body.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an end of the No. 3 black out tape and pull it parallel to the vehicle body to pull it off.



17. REMOVE NO. 2 BLACK OUT TAPE
  1. Using a heat light, heat the No. 2 black out tape and vehicle body.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an end of the No. 2 black out tape and pull it parallel to the vehicle body to pull it off.



18. REMOVE INNER UPPER BLACK OUT REAR DOOR TAPE
  1. Using a heat light, heat the inner upper black out rear door tape and vehicle body.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an end of the inner upper black out rear door tape and pull it parallel to the vehicle body to pull it off.



19. REMOVE INNER FRONT BLACK OUT REAR DOOR TAPE
  1. Using a heat light, heat the inner front black out rear door tape and vehicle body.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an end of the inner front black out rear door tape and pull it parallel to the vehicle body to pull it off.



20. REMOVE INNER REAR BLACK OUT REAR DOOR TAPE
  1. Using a heat light, heat the inner rear black out rear door tape and vehicle body.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an end of the inner rear black out rear door tape and pull it parallel to the vehicle body to pull it off.