Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0102    Mass or Volume Air Flow Circuit Low Input

DTC    P0103    Mass or Volume Air Flow Circuit High Input

for Preparation Click here


DESCRIPTION

The mass air flow meter is a sensor that measures the amount of air flowing through the valve.
The ECM (included in the hybrid vehicle control ECU) uses this information to determine the fuel injection duration and to provide an appropriate air-fuel ratio.
Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air.
By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the mass air flow meter. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and the temperature sensor provide a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:
When any of these DTCs are set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine RPM and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A140749E02


DTC No.
DTC Detection Condition
Trouble Area
P0102
Open in mass air flow meter circuit for 3 seconds
  1. Open in mass air flow meter circuit
  2. Short in mass air flow meter circuit
  3. Mass air flow meter
  4. Hybrid vehicle control ECU
P0103
Short in mass air flow meter circuit for 3 seconds
  1. Short in mass air flow meter circuit (+B circuit)
  2. Mass air flow meter
  3. Hybrid vehicle control ECU

HINT:
When any of these DTCs are set, check the air-flow rate by entering the following menus on the Techstream: Powertrain / Engine and ECT / Data List / MAF.

Mass Air Flow Rate (gm/s)
Malfunctions
Approximately 0.0
  1. Open in mass air flow meter power source circuit
  2. Open or short in VG circuit
271.0 or more
Open in EVG circuit


MONITOR DESCRIPTION

If there is a defect in the mass air flow meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM (included in the hybrid vehicle control ECU) interprets this deviation as a malfunction in the mass air flow meter and sets a DTC.
Example:
When the sensor output voltage remains less than 0.2 V, or more than 4.9 V, for more than 3 seconds, the ECM sets a DTC.
If the malfunction is not repaired successfully, a DTC is set 3 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0102: Mass air flow meter range check (Low voltage)
P0103: Mass air flow meter range check (High voltage)
Required Sensors/Components (Main)
Mass air flow meter
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
3 seconds
MIL Operation
Immediate: Engine RPM less than 4000 rpm
2 driving cycles: Engine RPM 4000 rpm or more
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None

TYPICAL MALFUNCTION THRESHOLDS


P0102: 
Mass air flow meter voltage
Less than 0.2 V

P0103: 
Mass air flow meter voltage
More than 4.9 V

COMPONENT OPERATING RANGE


Mass air flow meter voltage
Between 0.2 V and 4.9 V

WIRING DIAGRAM


A179769E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF

  1. Read the values displayed on the Techstream.

    Result:

    Mass Air Flow Rate (gm/s)
    Proceed to
    0.0
    A
    271.0 or more
    B
    Between 1.0 and 270.0 (*1)
    C

    *1: The value should be changed when the throttle valve is open or closed.



B
Go to step 6

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.INSPECT MASS AIR FLOW METER


    A178384E02
  1. Disconnect the mass air flow meter connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    B10-1 (+B) - Body ground
    Power switch on (IG)
    9 to 14 V

  1. Reconnect the mass air flow meter connector.



NG
Go to step 5
OK


3.INSPECT HYBRID VEHICLE CONTROL ECU


    A178385E02
  1. Put the engine in inspection mode (Click here).

  1. Start the engine.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    B1-30 (VG) - B1-29 (EVG)
    Engine idling
    0.5 to 3.0 V



NG
Go to step 4
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)  

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - HYBRID VEHICLE CONTROL ECU)


    A178386E03
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B10-3 (VG) - B1-30 (VG)
    Always
    Below 1 Ω
    B10-2 (E2G) - B1-29 (EVG)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B10-3 (VG) or B1-30 (VG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the hybrid vehicle control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - HYBRID VEHICLE CONTROL ECU)
OK

REPLACE MASS AIR FLOW METER (Click here)  

5.INSPECT FUSE (EFI NO. 3 FUSE)


    A179777E02
  1. Remove the EFI No. 3 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B10-1 (+B) - EFI No. 3 fuse (2)
    Always
    Below 1 Ω

  1. Reconnect the mass air flow meter connector.

  1. Reinstall the EFI No. 3 fuse.



NG
REPLACE FUSE (IGCT FUSE)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - IGCT RELAY) 

6.INSPECT HYBRID VEHICLE CONTROL ECU


    A178385E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B1-29 (EVG) - Body ground
    Always
    Below 1 Ω



NG
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - HYBRID VEHICLE CONTROL ECU)


    A178386E04
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B10-3 (VG) - B1-30 (VG)
    Always
    Below 1 Ω
    B10-2 (E2G) - B1-29 (EVG)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B10-3 (VG) or B1-30 (VG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the hybrid vehicle control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER (Click here)