Home › ENGINE › 3MZ-FE FUEL › FUEL PRESSURE REGULATOR

FUEL PRESSURE REGULATOR > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
(Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT FLOOR COVER LH


4. REMOVE FRONT CENTER FLOOR COVER


5. REMOVE CENTER EXHAUST PIPE ASSEMBLY

HINT:
.



6. REMOVE NO. 3 FRONT FLOOR HEAT INSULATOR


    A175798
  1. Remove the 5 nuts and No. 3 front floor heat insulator.



7. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY


    A175799
  1. Disengage the 4 grommets.

  1. Remove the screw and No. 1 fuel tank protector sub-assembly.



8. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY


    A175800
  1. Remove the nut and disconnect the No. 3 parking brake cable assembly.



9. DISCONNECT FUEL TANK WIRE


    A108210
  1. Separate the fuel tank wire connector from the bracket.

  1. Disconnect the 2 connectors.



10. DISCONNECT FUEL TANK VENT HOSE


    A175801E01
  1. Disconnect the charcoal canister fuel hose from the fuel vapor containment valve.

    1. Pinch the retainer and pull out the quick connector with the quick connector pushed to the pipe side to disconnect the charcoal canister fuel hose from the fuel vapor containment valve.

      NOTICE:
      1. Remove dirt or foreign objects on the quick connector before this work.
      2. Be careful not to allow foreign matter to scratch or come into contact with the pipe that is sealed by O-rings.
      3. Perform this work by hand. Do not use any tools.
      4. Do not forcibly bend, twist or turn the nylon tube.
      5. Protect the connected part by covering it with a plastic bag after disconnecting the charcoal canister fuel hose.
      6. If the quick connector and pipe are stuck, push and pull them to release.



11. DISCONNECT FUEL PUMP TUBE SUB-ASSEMBLY


    A112343E02
  1. Pinch the tabs of the retainer to disengage the lock claws and pull the retainer down as shown in the illustration.

  1. Pull out the fuel pump tube.

    NOTICE:
    1. Check for dirt or other foreign objects around the connector before this operation. Clean the connector as necessary.
    2. Be careful not to allow mud or foreign matter to scratch or come into contact with the pipe and connector that are sealed by O-rings.
    3. Do not use any tools for this operation.
    4. Do not damage the disconnected pipe and connector. Prevent intrusion of foreign objects by covering the pipe and connector with a plastic bag.
    5. When the pipe and connector are stuck, push and pull the connector to release. Pull out the connector carefully.



12. DISCONNECT NO. 1 FUEL TANK BREATHER TUBE


    A108207E02
  1. Remove the checker of the No. 1 fuel tank breather tube connector.

  1. Pinch the retainer of the No. 1 fuel tank breather tube connector, and pull out the No. 1 fuel tank breather tube connector to disconnect the No. 1 fuel tank breather tube from the fuel tank.

    NOTICE:
    1. Check for dirt around the connector before this operation. Remove the dirt as necessary.
    2. Be careful not to allow mud or foreign matter to scratch or come into contact with the pipe and connector that are sealed by O-rings.
    3. Do not use any tool in this operation.
    4. Do not damage the disconnected pipe and connector. Prevent intrusion of foreign objects by covering the pipe and connector with a plastic bag.
    5. When the pipe and the connector are stuck, push and pull the connector to release. Pull out the connector carefully.



13. REMOVE FUEL TANK ASSEMBLY


    A175802E01
  1. Set an engine lifter to the fuel tank.

  1. Remove the fuel filler pipe clamp and fuel tube connector from the fuel tank inlet pipe.



    A175803
  1. Remove the 4 bolts and the fuel tank bands.

  1. Operate the engine lifter, and disconnect the fuel inlet pipe.

  1. Operate the engine lifter, and remove the fuel tank.



14. REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE


    A108215E03
  1. Disconnect the fuel pump connector (A).

  1. Disconnect the clamp and vapor pressure sensor connector (B).



    A108216E02
  1. Remove the tube joint clip and clamp, and pull out the fuel pump tube.

    NOTICE:
    1. Check that there is no dirt or foreign matter around the fuel tube joint and after cleaning off any excess dirt, proceed with the work.
    2. Be careful not to allow dirt or foreign matter to scratch or come into contact with the fuel tube connector and fuel suction plate that are sealed by O-rings.
    3. Do not use any tools for this work.
    4. Do not bend or twist the nylon tube by force.
    5. Cover the disconnected fuel tube joint with a plastic bag.
    6. When the fuel tube joint and fuel suction plate are stuck, pinch the fuel tank tube with the fingers, and turn it carefully to release. Disconnect the fuel tank tube.



    A108217
  1. Remove the 8 bolts, fuel tank vent tube set plate and fuel pump connector plate.



    A154761
  1. Pull out the fuel suction tube assembly from the fuel tank.

    NOTICE:
    1. Do not damage the fuel pump filter.
    2. Be careful not to bend the arm of the sender gauge.

  1. Remove the gasket from the fuel suction tube assembly.



15. REMOVE FUEL SENDER GAUGE ASSEMBLY


    A182856E01
  1. Disconnect the fuel sender gauge connector (A).

  1. Unlock the fuel sender gauge, then slide and remove it (B).



16. REMOVE NO. 2 FUEL SUCTION SUPPORT


    A182857
  1. Using a screwdriver with its tip wrapped with tape, disengage the 4 snap claws from the claw holes, and remove the fuel suction support.

    NOTICE:
    Do not damage the fuel suction support.



17. REMOVE FUEL PUMP CUSHION RUBBER


    A182858
  1. Remove the fuel pump cushion rubber from the fuel pump.



18. REMOVE FUEL PRESSURE REGULATOR ASSEMBLY


    A182865
  1. Remove the fuel pressure regulator assembly from the fuel tank fuel filter.



    A108182E01
  1. Remove the O-ring from the fuel pressure regulator assembly.