FUEL PRESSURE PULSATION DAMPER > REMOVAL |
| 1. DISCHARGE FUEL SYSTEM PRESSURE |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Remove the nut, and the front wiper arm and blade assembly LH.
| 4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Remove the nut, and the front wiper arm and blade assembly RH.
| 5. REMOVE HOOD TO COWL TOP SEAL |
![]() |
Disengage the 8 clips and remove the hood to cowl top seal.
| 6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Disengage the 2 claws and disconnect the front fender to cowl side seal LH.
![]() |
Disengage the 2 claws and disconnect the front fender to cowl side seal RH.
Remove the 2 clips.

Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.
| 7. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 4 bolts, and the windshield wiper motor and link assembly.
| 8. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY |
![]() |
Disengage the 4 clamps and separate the wiper wire harness from the outer cowl top panel sub-assembly.
![]() |
Remove the 8 bolts, 6 nuts, and the outer cowl top panel sub-assembly.
| 9. REMOVE COOL AIR INTAKE DUCT SEAL |
Remove the 11 clips and cool air intake duct seal.
| 10. REMOVE NO. 2 ENGINE ROOM SIDE COVER LH |
![]() |
Remove the engine room side cover.
| 11. DRAIN ENGINE COOLANT (for Engine) |
Loosen the radiator drain cock plug.
Loosen the cylinder block drain cock plugs.
Remove the radiator cap.

| 12. REMOVE AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Remove the 2 bolts, 4 clamps and air cleaner cap sub-assembly.
Remove the air cleaner filter element from the air cleaner case.
| 13. REMOVE AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Separate the No. 1 ventilation hose.
![]() |
Disconnect the intake air flow meter connector.
Disconnect the 2 wire harness clamps from the air cleaner case sub-assembly.
![]() |
Remove the 5 bolts from the air cleaner case sub-assembly.
![]() |
Loosen the hose clamp and separate the No. 1 air cleaner hose.
Remove the air cleaner case sub-assembly.
| 14. REMOVE AIR CLEANER BRACKET |
![]() |
Remove the 2 bolts and air cleaner bracket.
| 15. REMOVE EMISSION CONTROL VALVE SET |
![]() |
Disconnect the VSV connector (A).
Remove the wire harness clamp (B).
Disconnect the No. 1 fuel vapor feed hose (C).
Disconnect the No. 2 fuel vapor feed hose (D).
Remove the 2 nuts (E), then remove the emission control valve set.
| 16. REMOVE INTAKE AIR SURGE TANK |
![]() |
Disconnect the throttle motor connector (A).
Separate the No. 2 water by-pass hose (B).
Separate the No. 3 water by-pass hose (C).
Separate the fuel vapor feed hose (D).
![]() |
Disconnect the ventilation hose.
![]() |
Remove the 2 bolts and No. 1 engine hanger (A).
Remove the 2 bolts and No. 1 surge tank stay (B).
Remove the 2 bolts and No. 2 surge tank stay (C).
![]() |
Disconnect the ground cable connector.
Using a socket hexagon wrench 8 mm, remove the 4 bolts.
Remove the 2 nuts, then remove the emission control valve bracket and the intake air surge tank.
Remove the gasket from the intake air surge tank.
| 17. REMOVE FUEL PRESSURE PULSATION DAMPER ASSEMBLY |
![]() |
Remove the bolt and separate the No. 1 fuel pipe (A).
Remove the fuel pressure pulsation damper and the 2 gaskets (B).
Remove the No. 2 fuel pipe union bolt and the 2 gaskets (C).