Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

DTC    P0AA1-233    Hybrid Battery Positive Contactor Circuit Stuck Closed

for Preparation Click here


DESCRIPTION

  1. Refer to the description for DTC P0AE6-225 .
  2. This circuit uses the hybrid vehicle control ECU to monitor the system main relays and stops the system if a malfunction is detected in the relays, because it may be impossible to shut off the high-voltage system if any of the relays becomes stuck.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0AA1
233
SMR1, SMR2. or SMR3 on the HV battery positive and negative sides stuck closed
HV relay assembly

WIRING DIAGRAM

See the wiring diagram of P0AE6-225 .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After disconnecting the service plug grip, wait for at least 5 minutes before touching any of the high-voltage connectors or terminals. After waiting for 5 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:
  1. Waiting for at least 5 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
  2. If P0AA1-233 is output, the hybrid system cannot be turned on.

1.CHECK DTC OUTPUT (HV)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0A78-523 is not output
    A
    P0A78-523 is output
    B



B
GO TO DTC CHART (Click here)
A


2.CHECK HV RELAY ASSEMBLY

CAUTION:
Be sure to wear insulated gloves.

  1. Turn the power switch off.



    A108057E07
  1. Remove the service plug grip (Click here).

    CAUTION:
    Do not reinsert the service plug grip until replacement of the HV relay assembly is completed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Measure the resistance according to the value(s) in the table below. (Inspection of SMR1 and SMR2)

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    z30-1 - j2-1
    Power switch off
    10 kΩ or higher

    HINT:
    1. If a system main relay is stuck closed, inspect the HV relay assembly without removing it from the vehicle, in order to keep the relay closed.
    2. If P0AA1-233 is output, the HV relay assembly must be replaced. Measuring resistance can determine if this is either a present or past malfunction.
    3. If the resistance is between 28.5 and 31.5 Ω, it can be determined that SMR1 is stuck closed.



    A108056E07
  1. Measure the resistance according to the value(s) in the table below. (Inspection of SMR3)

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    z31-1 - j3-1
    Power switch off
    10 kΩ or higher

    HINT:
    1. If a system main relay is stuck closed, inspect the HV relay assembly without removing it from the vehicle, in order to keep the relay closed.
    2. If P0AA1-233 is output, the HV relay assembly must be replaced. Measuring resistance can determine if this is either a present or past malfunction.



NG
REPLACE HV RELAY ASSEMBLY (Click here)
OK

REPLACE HV RELAY ASSEMBLY (Click here)