Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3160E _57 Power Source / Network _019704 NETWORKING _0095459 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1206  P/W Master Switch Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the power window regulator master switch assembly and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1206 P/W Master Switch Communication Stop No communication between power window regulator master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Power window regulator master switch assembly

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector

·

A/C fuse



WIRING DIAGRAM

for LHD


B365180
0.25,2.063 1.885,2.573 1.635,0.51 10 false Main Body ECU (Multiplex Network Body ECU) 6.333,0.781 6.792,0.979 0.458,0.198 10 false A/C 0.25,1.906 0.563,2.104 0.313,0.198 10 false MB 1.469,0.927 1.813,1.167 0.344,0.24 10 false LIN2 1.958,1.604 2.271,1.802 0.313,0.198 10 false 4D 1.958,1.76 3.594,2.198 1.635,0.438 10 false Instrument Panel Junction Block Assembly 1.865,0.781 2.177,0.979 0.313,0.198 10 false 16 3.146,0.771 3.458,0.969 0.313,0.198 10 false 25 0.708,3.344 2.438,3.542 1.729,0.198 10 false : LIN Communication Line 4.427,1.885 5.323,2.094 0.896,0.208 10 false I7 4.427,2.052 6,2.427 1.573,0.375 10 false Power Window Regulator Master Switch Assembly 5.313,1.469 5.656,1.708 0.344,0.24 10 false GND 5.51,0.646 5.667,0.844 0.156,0.198 10 false B 4.781,0.927 5.125,1.167 0.344,0.24 10 false LIN1 4.5,0.76 5.115,0.958 0.615,0.198 10 false 17 5.698,0.5 6.313,0.698 0.615,0.198 10 false 11 5.708,1.365 6.323,1.563 0.615,0.198 10 false 12


for RHD


B365180
0.167,1.896 0.479,2.094 0.313,0.198 10 false MB 0.167,2.052 1.823,2.469 1.656,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 1.948,1.594 2.26,1.792 0.313,0.198 10 false 4D 1.948,1.75 3.542,2.146 1.594,0.396 10 false Instrument Panel Junction Block Assembly 0.719,3.313 2.427,3.531 1.708,0.219 10 false : LIN Communication Line 1.469,0.917 1.854,1.135 0.385,0.219 10 false LIN2 1.865,0.771 2.177,0.969 0.313,0.198 10 false 16 3.135,0.76 3.448,0.958 0.313,0.198 10 false 25 4.385,0.583 5,0.781 0.615,0.198 10 false 17*1 4.458,0.76 5.073,0.958 0.615,0.198 10 false 6*2 4.781,0.927 5.167,1.146 0.385,0.219 10 false LIN1 5.51,0.646 5.667,0.844 0.156,0.198 10 false B 5.313,1.479 5.698,1.698 0.385,0.219 10 false GND 5.698,0.375 6.313,0.573 0.615,0.198 10 false 11*1 5.708,0.542 6.323,0.74 0.615,0.198 10 false 3*2 6.323,0.771 6.781,0.969 0.458,0.198 10 false A/C 5.708,1.188 6.323,1.385 0.615,0.198 10 false 12*1 5.719,1.354 6.333,1.552 0.615,0.198 10 false 1*2 4.438,1.875 5.375,2.083 0.938,0.208 10 false H7*1, H6*2 4.438,2.052 6.031,2.469 1.594,0.417 10 false Power Window Regulator Master Switch Assembly 3.323,2.958 6.99,3.198 3.667,0.24 10 false *1: for Models with Jam Protection Function on 4 Windows 3.323,3.281 6.99,3.521 3.667,0.24 10 false *2: for Models with Jam Protection Function on 2 Windows


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B345099
2.083,0.917 2.417,1.167 0.333,0.25 5.417,0.667 5.75,0.917 0.333,0.25 2,2 2.198,1.583 false 2.167,0.969 2.479,1.167 0.313,0.198 10 false MB 0.354,0.333 0.667,0.531 0.313,0.198 10 false *a 5.51,0.708 5.823,0.906 0.313,0.198 10 false 4D 1.854,2.052 2.167,2.25 0.313,0.198 10 false LIN2
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
4D-25 - MB-16 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
a.

for LHD

i.

Disconnect the I7 power window regulator master switch assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4D-25 - I7-17 (LIN1) Ignition switch off Below 1 Ω
I7-17 (LIN1) or 4D-25 - Body ground Ignition switch off 10 kΩ or higher




b.

for RHD

i.

Disconnect the H7*1 or H6*2 power window regulator master switch assembly connector.

*1: for Models with Jam Protection Function on 4 Windows

*2: for Models with Jam Protection Function on 2 Windows



ii.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4D-25 - H7-17 (LIN1)*1 Ignition switch off Below 1 Ω
4D-25 - H6-6 (LIN1)*2 Ignition switch off Below 1 Ω
H7-17 (LIN1) or 4D-25 - Body ground*1 Ignition switch off 10 kΩ or higher
H6-6 (LIN1) or 4D-25 - Body ground*2 Ignition switch off 10 kΩ or higher


*1: for Models with Jam Protection Function on 4 Windows

*2: for Models with Jam Protection Function on 2 Windows




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY, BODY GROUND)
a.

for LHD

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I7-11 (B) - I7-12 (GND) Always 11 to 14 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I7-12 (GND) - Body ground Always Below 1 Ω




b.

for RHD

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H7-11 (B) - H7-12 (GND)*1 Always 11 to 14 V
H6-3 (B) - H6-1 (GND)*2 Always 11 to 14 V


*1: for Models with Jam Protection Function on 4 Windows

*2: for Models with Jam Protection Function on 2 Windows



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H7-12 (GND) - Body ground*1 Always Below 1 Ω
H6-1 (GND) - Body ground*2 Always Below 1 Ω


*1: for Models with Jam Protection Function on 4 Windows

*2: for Models with Jam Protection Function on 2 Windows




Result:
Proceed to
OK
NG



OK

4.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Replace the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Recheck for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B1206 is not output.



Result:
Proceed to
OK
NG



OK

END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)