Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU
RM3160E _57 Power Source / Network _019703 POWER DISTRIBUTION _0100762 MAIN BODY ECU A

POWER DISTRIBUTION  MAIN BODY ECU  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


for LHD
·

To prevent damage to the main body ECU (multiplex network body ECU), disconnect the cable from the negative (-) battery terminal and discharge the door control battery before replacing or removing/installing the main body ECU (multiplex network body ECU).



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


a.

Discharge the door control battery. (for LHD)

HINT:

The door control battery will discharge completely within approximately 30 minutes after the ignition switch is turned off.

The time required to discharge the door control battery is reduced when it is not fully charged.


i.

Connect the GTS to the DLC3.


ii.

Turn the GTS on.


iii.

Enter the following menus: Body Electrical / Main Body / Active Test.


iv.

Disconnect the cable from the negative (-) battery terminal.


v.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Shock Detection Unlock Operate door lock motor UNLOCK/LOCK -
Body Electrical > Main Body > Active Test
Tester Display
Shock Detection Unlock
50004 123 21
HINT:

Perform the Active Test until the door lock/unlock operation can no longer be performed and "Lost communication with vehicle" is displayed on the GTS.




Hide 67914 3.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112A 4.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 5.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 55436A 6.REMOVE INSTRUMENT PANEL FINISH PANEL END LH

Hide 55606 7.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

Hide 53601 8.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for LHD)

Hide 55045 9.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for LHD)

Hide 55607 10.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

Hide 55303B 11.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)

Hide 12.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for LHD)

a.
B322883

Disconnect each connector.


b.
B322884

Disengage the claw and pull down the lock lever to disconnect the connector as shown in the illustration.


c.
B322886

Disengage the claw and pull down the lock lever to disconnect the connector as shown in the illustration.


d.
B322889

Disengage the clamp.


e.
B322888

Remove the 2 nuts.


f.
B322890

Disengage the clamp as shown in the illustration.


g.

Pull out the instrument panel junction block assembly with main body ECU.


h.
B322892

Disengage the claw and raise the lock lever to disconnect the connector as shown in the illustration.


i.
B322894

Disengage the claw and slide the connector lock as shown in the illustration.


j.
B322896

Disengage the claw and raise the lock lever to disconnect the connector as shown in the illustration and remove the instrument panel junction block assembly with main body ECU.


Hide 13.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for RHD)

a.
B322906

Disconnect each connector.


b.
B322907

Disengage the claw and pull down the lock lever to disconnect the connector as shown in the illustration.


c.
B322909

Disengage the claw and pull down the lock lever to disconnect the connector as shown in the illustration.


d.
B322911

Disengage the clamp.


e.
B322912C01
1.177,1.875 1.135,1.917 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts and nut.


f.
B322913

Disengage the clamp as shown in the illustration.


g.
B322914

Disengage the claw and guide to disconnect the connector holder as shown in the illustration.


h.

Pull out the instrument panel junction block assembly with main body ECU.


i.
B322916

Disengage the claw and raise the lock lever to disconnect the connector as shown in the illustration.


j.
B322918

Disengage the claw and slide the connector lock as shown in the illustration.


k.
B322920

Disengage the claw and raise the lock lever to disconnect the connector as shown in the illustration and remove the instrument panel junction block assembly with main body ECU.


Hide 89221 14.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

a.

Press the claw of the instrument panel junction block assembly as shown in the illustration to release the lock.

B322922C01
0.854,2.26 1.833,2.313 true 4.281,2.25 4.917,2 true 0.792,2.385 0.792,2.615 0.792,2.615 1.75,2.615 true 4.219,2.396 4.219,2.625 4.219,2.625 5.177,2.625 true 0.615,0.167 1.01,0.427 0.396,0.26 12 false *A 4.042,0.167 4.406,0.375 0.365,0.208 12 false *B 1.885,2.25 2.198,2.406 0.313,0.156 10 false *1 1.792,2.542 2.104,2.698 0.313,0.156 10 false *2 4.938,1.906 5.25,2.063 0.313,0.156 10 false *1 5.229,2.552 5.542,2.708 0.313,0.156 10 false *2
*A for LHD *B for RHD
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU (Multiplex Network Body ECU)



b.

With the instrument panel junction block assembly lock released, insert a screwdriver with its tip wrapped with protective tape horizontally between the main body ECU (multiplex network body ECU) and instrument panel junction block assembly.

B322923C01
1.917,1.521 2.094,1.365 true 5.542,1.542 5.563,1.219 true 0.781,0.156 1.188,0.396 0.406,0.24 12 false *A 4.292,0.156 4.698,0.365 0.406,0.208 12 false *B 1.792,1.521 2.104,1.677 0.313,0.156 10 false *a 5.469,1.552 5.781,1.708 0.313,0.156 10 false *a
*A for LHD *B for RHD
*a Protective Tape - -


NOTICE:
·

Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).

·

Do not insert the screwdriver under the connector socket of the main body ECU (multiplex network body ECU).




c.

Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.

NOTICE:

Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).



d.

Raise the main body ECU (multiplex network body ECU) as shown by the arrow (1), and then pull it out as shown by the arrow (2) in the illustration.

B322924C01
0.688,0.125 1.073,0.375 0.385,0.25 12 false *A 4.25,0.125 4.625,0.375 0.375,0.25 12 false *B 0.833,0.531 0.99,0.729 0.156,0.198 10 false 1 4.385,0.469 4.542,0.667 0.156,0.198 10 false 1 2.552,1.396 2.708,1.594 0.156,0.198 10 false 2 6.031,1.177 6.188,1.375 0.156,0.198 10 false 2
*A for LHD *B for RHD


NOTICE:

Do not touch the main body ECU (multiplex network body ECU) connector.