Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095460 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Room Oscillator does not Recognize Key  


DESCRIPTION

If code verification cannot be performed in the vehicle interior, there may be problems with the communication between the vehicle (indoor electrical key antenna assembly (front floor), (rear floor) or (inside luggage compartment)) and electrical key transmitter sub-assembly, or the certification ECU (smart key ECU assembly) may be malfunctioning. When the electrical key transmitter sub-assembly is brought into the vehicle, verification of the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) is performed. If verification cannot be performed or the codes do not match, the engine switch cannot be turned on (IG) and the engine cannot be started.

When a door is unlocked and the electrical key transmitter sub-assembly is brought into the vehicle, the certification ECU (smart key ECU assembly) activates the indoor electrical key antenna assembly which transmits radio waves to detect the electrical key transmitter sub-assembly. If the electrical key transmitter sub-assembly recognizes that it is in the detection area, it responds with the key ID code. This information is received by the indoor electrical key antenna assembly and then sent to the certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B300397E18
5.417,0.99 5.99,1.333 0.573,0.344 10 false CG5B 2.031,0.969 2.438,1.135 0.406,0.167 10 false CLGB 2.521,0.875 2.75,1.094 0.229,0.219 10 false 3 1.958,0.615 2.583,0.896 0.625,0.281 10 false ANTE5 0.875,1.25 1.167,1.417 0.292,0.167 10 false F39 0.875,1.417 3.135,1.906 2.26,0.49 10 false No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) 2.521,0.5 2.656,0.667 0.135,0.167 10 false 1 5.094,0.396 5.333,0.573 0.24,0.177 10 false 21 5.417,0.604 5.823,0.771 0.406,0.167 10 false CLG5 5.104,0.781 5.292,0.948 0.188,0.167 10 false 20 5.427,2.74 5.906,2.969 0.479,0.229 10 false CG6B 2.042,2.74 2.771,3.083 0.729,0.344 10 false CLGB 2.521,2.646 2.729,2.844 0.208,0.198 10 false 3 1.969,2.365 2.594,2.646 0.625,0.281 10 false ANTE6 0.885,3.031 1.229,3.198 0.344,0.167 10 false M18 0.875,3.188 3.125,3.656 2.25,0.469 10 false No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor) 2.521,2.271 2.698,2.49 0.177,0.219 10 false 1 5.083,2.177 5.292,2.344 0.208,0.167 10 false 15 5.427,2.365 5.833,2.531 0.406,0.167 10 false CLG6 5.083,2.552 5.292,2.719 0.208,0.167 10 false 14 5.083,4.958 6.615,5.458 1.531,0.5 10 false Certification ECU (Smart Key ECU Assembly) 5.063,2.74 5.385,2.906 0.323,0.167 10 false F12 5.063,2.365 5.385,2.531 0.323,0.167 10 false F12 5.073,0.969 5.396,1.135 0.323,0.167 10 false F13 5.073,0.594 5.385,0.76 0.313,0.167 10 false F13 5.417,4.427 5.823,4.594 0.406,0.167 10 false CG7B 5.135,3.865 5.344,4.031 0.208,0.167 10 false 4 5.417,4.073 5.823,4.24 0.406,0.167 10 false CLG7 5.135,4.25 5.344,4.417 0.208,0.167 10 false 3 5.063,4.438 5.396,4.604 0.333,0.167 10 false F12 5.063,4.063 5.365,4.229 0.302,0.167 10 false F12 2.031,4.438 2.49,4.74 0.458,0.302 10 false CLGB 2.521,4.344 2.708,4.552 0.188,0.208 10 false 3 1.958,4.073 2.531,4.365 0.573,0.292 10 false ANTE7 2.51,3.958 2.688,4.135 0.177,0.177 10 false 1 0.573,4.708 0.958,4.875 0.385,0.167 10 false O1 0.573,4.875 3.479,5.292 2.906,0.417 10 false No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment)

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to smart entry and start system (for Entry Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

The indoor electrical key antenna assemblies have an antenna coil between each terminal.

·

The smart door control receiver assembly is also related to interior verification.



PROCEDURE

1.CHECK START OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check that the engine starts.


Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

B

2.CHECK ENTRY LOCK OPERATION
2.CHECK ENTRY LOCK OPERATION
a.

Check that the entry lock and unlock functions operate on each door.

HINT:

If the smart door control receiver assembly is defective, code verification does not begin in the cabin and the entry lock and unlock functions do not operate.



Result:
Result Proceed to
All door entry functions operate normally A
All door entry functions does not operate normally B



A

3.CHECK PUSH-BUTTON START FUNCTION

B

3.CHECK PUSH-BUTTON START FUNCTION
a.
B358060C01
1.125,0.667 1,0.365 1,0.365 0.833,0.365 false 2.177,1.635 2.26,1.948 2.26,1.948 2.417,1.948 false 0.667,0.313 0.979,0.469 0.313,0.156 10 false *1 2.49,1.875 2.802,2.031 0.313,0.156 10 false *2
*1 Engine Switch
*2 Electrical Key Transmitter Sub-assembly


Remove the transmitter battery of the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT


b.

With the brake pedal depressed, face the logo side of the electrical key transmitter sub-assembly towards the engine switch, hold the transmitter near the engine switch and then press the engine switch.


c.

When operating the engine switch, check whether the engine starts.

HINT:
·

When the electrical key transmitter sub-assembly cannot be verified even though it is inside the detection area, the engine start check can be performed by removing the transmitter battery from the electrical key transmitter sub-assembly and holding the electrical key transmitter sub-assembly near the engine switch.

·

If the engine cannot be started when performing this inspection, the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) may be malfunctioning.



OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

4.CHECK WAVE ENVIRONMENT

NG

4.CHECK WAVE ENVIRONMENT
a.

Install the transmitter battery to the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT


b.

Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (front floor) and perform a smart entry and start system check.

Click here

NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).



c.

Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key antenna assembly (rear floor) and perform a smart entry and start system check.

Click here

HINT:

Check that the customize status of the "Ignition Available Area" has been "All".


NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 2 indoor electrical key antenna assembly (rear floor).



d.

Bring the electrical key transmitter sub-assembly near the No. 3 indoor electrical key antenna assembly (inside luggage compartment) and perform a smart entry and start system check.

Click here

HINT:

Check that the customize status of the "Ignition Available Area" has been "All".


NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 3 indoor electrical key antenna assembly (inside luggage compartment).



HINT:
·

As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

The engine starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the engine switch is pressed.


Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

6.CHECK KEY DIAGNOSTIC MODE

NG

6.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

b.

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

i.
B358003C01
0.677,1.125 2.375,0.271 2.375,0.271 2.625,0.271 false 1.781,1.104 2.365,0.281 false 2.719,0.167 3.031,0.323 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (front floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.


ii.
B358004C01
0.656,0.292 2.198,0.115 2.198,0.115 2.354,0.115 false 1.792,0.281 2.177,0.115 false 2.427,0.042 2.74,0.198 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna assembly (rear floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.


iii.
B358015C01
1.198,1.365 2.365,0.354 2.365,0.354 2.708,0.354 false 1.667,1.281 2.365,0.354 false 2.771,0.281 3.083,0.479 0.313,0.198 10 false *a
*a Inspection Point


Check the No. 3 indoor electrical key antenna assembly (inside luggage compartment).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

·

It is possible to check which indoor electrical key antenna assembly (front floor, rear floor or inside luggage compartment) is operating by the sounding of the buzzer.

·

When the wireless buzzer sounds for all indoor electrical key antenna assemblies, they can be judged as operating properly and a malfunction in the certification ECU (smart key ECU assembly), which performs verification, is suspected.

·

When the wireless buzzer does not sound for all indoor electrical key antenna assemblies, it can be judged that the certification ECU (smart key ECU assembly), which controls the indoor electrical key antenna assemblies, is malfunctioning.





Result:
Result Proceed to
The wireless buzzer sounds/does not sound for all indoor electrical key antenna assemblies A
The wireless buzzer does not sound for only the No. 1 indoor electrical key antenna assembly (front floor) B
The wireless buzzer does not sound for only the No. 2 indoor electrical key antenna assembly (rear floor) C
The wireless buzzer does not sound for only the No. 3 indoor electrical key antenna assembly (inside luggage compartment) D



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

C

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

D

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))
7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))
a.

Disconnect the F13 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F39 No. 1 indoor electrical key antenna assembly (front floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-21 (CLG5) - F39-1 (ANTE5) Always Below 1 Ω
F13-20 (CG5B) - F39-3 (CLGB) Always Below 1 Ω
F13-21 (CLG5) or F39-1 (ANTE5) - Body ground Always 10 kΩ or higher
F13-20 (CG5B) or F39-3 (CLGB) - Body ground Always 10 kΩ or higher



d.

Reconnect the F13 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

8.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))
a.
B343201C20
1.552,0.417 1.896,0.646 0.344,0.229 1.063,1.896 1.448,1.677 true 2.385,1.875 1.979,1.698 true 0.635,1.844 1.406,2.042 0.771,0.198 10 false ANTE5 2.417,1.844 3.188,2.042 0.771,0.198 10 false CLGB 1.615,0.458 2.385,0.656 0.771,0.198 10 false F39 0.542,0.385 1.313,0.583 0.771,0.198 10 false *a 0.688,2.229 1.458,2.427 0.771,0.198 10 false *b 0.292,3.344 1.063,3.542 0.771,0.198 10 false GND 1.208,4.177 1.5,4.385 0.292,0.208 10 false *c 2.115,4.188 2.406,4.396 0.292,0.208 10 false *d
*a Front view of wire harness connector
(to No. 1 Indoor Electrical Key Antenna Assembly (Front Floor))
*b Waveform 1
*c For 30 seconds after closing any door using the door outside handle
*d 30 seconds or more have elapsed after closing any door using the door outside handle


Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
F39-1 (ANTE5) - F39-3 (CLGB) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

9.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)
a.

Temporarily replace the No. 1 indoor electrical key antenna assembly (front floor) with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Front Floor)>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CHECK KEY DIAGNOSTIC MODE
10.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

b.

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

i.
B358003C01
0.677,1.125 2.375,0.271 2.375,0.271 2.625,0.271 false 1.781,1.104 2.365,0.281 false 2.719,0.167 3.031,0.323 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (front floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



OK:

Wireless buzzer sounds.




Result:
Proceed to
OK
NG



OK

END (NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))
a.

Disconnect the F12 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the M18 No. 2 indoor electrical key antenna assembly (rear floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F12-15 (CLG6) - M18-1 (ANTE6) Always Below 1 Ω
F12-14 (CG6B) - M18-3 (CLGB) Always Below 1 Ω
F12-15 (CLG6) or M18-1 (ANTE6) - Body ground Always 10 kΩ or higher
F12-14 (CG6B) or M18-3 (CLGB) - Body ground Always 10 kΩ or higher



d.

Reconnect the F12 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

12.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))
a.
B343201C24
1.552,0.417 1.896,0.646 0.344,0.229 1.063,1.896 1.448,1.677 true 2.385,1.875 1.979,1.698 true 0.635,1.844 1.406,2.042 0.771,0.198 10 false ANTE6 2.417,1.844 3.188,2.042 0.771,0.198 10 false CLGB 1.583,0.438 2.354,0.635 0.771,0.198 10 false M18 0.542,0.385 1.313,0.583 0.771,0.198 10 false *a 0.688,2.229 1.458,2.427 0.771,0.198 10 false *b 0.25,3.333 1.021,3.531 0.771,0.198 10 false GND 1.208,4.177 1.5,4.385 0.292,0.208 10 false *c 2.115,4.188 2.406,4.396 0.292,0.208 10 false *d
*a Front view of wire harness connector
(to No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor))
*b Waveform 1
*c For 30 seconds after closing any door using the door outside handle
*d 30 seconds or more have elapsed after closing any door using the door outside handle


Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
M18-1 (ANTE6) - M18-3 (CLGB) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

13.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

13.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)
a.

Temporarily replace the No. 2 indoor electrical key antenna assembly (rear floor) with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Front Floor)>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK KEY DIAGNOSTIC MODE
14.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

b.

Select either channel 1 or channel 2 and inspect the diagnostic mode for each channel.

i.
B358004C01
0.656,0.292 2.198,0.115 2.198,0.115 2.354,0.115 false 1.792,0.281 2.177,0.115 false 2.427,0.042 2.74,0.198 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna assembly (rear floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



OK:

Wireless buzzer sounds.




Result:
Proceed to
OK
NG



OK

END (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))
a.

Disconnect the F12 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the O1 No. 3 indoor electrical key antenna assembly (inside luggage compartment) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F12-4 (CLG7) - O1-1 (ANTE7) Always Below 1 Ω
F12-3 (CG7B) - O1-3 (CLGB) Always Below 1 Ω
F12-4 (CLG7) or O1-1 (ANTE7) - Body ground Always 10 kΩ or higher
F12-3 (CG7B) or O1-3 (CLGB) - Body ground Always 10 kΩ or higher



d.

Reconnect the F12 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

16.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))
a.
B343201C22
1.552,0.417 1.896,0.646 0.344,0.229 1.063,1.896 1.448,1.677 true 2.385,1.875 1.979,1.698 true 0.604,1.844 1.375,2.042 0.771,0.198 10 false ANTE7 2.417,1.844 3.188,2.042 0.771,0.198 10 false CLGB 1.635,0.458 2.406,0.656 0.771,0.198 10 false O1 0.542,0.385 1.313,0.583 0.771,0.198 10 false *a 0.688,2.229 1.458,2.427 0.771,0.198 10 false *b 0.26,3.344 1.031,3.542 0.771,0.198 10 false GND 1.208,4.177 1.5,4.385 0.292,0.208 10 false *c 2.115,4.188 2.406,4.396 0.292,0.208 10 false *d
*a Front view of wire harness connector
(to No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment))
*b Waveform 1
*c For 30 seconds after closing any door using the door outside handle
*d 30 seconds or more have elapsed after closing any door using the door outside handle


Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
O1-1 (ANTE7) - O1-3 (CLGB) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

17.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

17.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT)
a.

Temporarily replace the No. 3 indoor electrical key antenna assembly (inside luggage compartment) with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Luggage Compartment)>REMOVAL


Result:
Proceed to
NEXT



NEXT

18.CHECK KEY DIAGNOSTIC MODE
18.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

b.

Select either channel 1 or channel 2 and inspect the diagnostic mode for each channel.

i.
B358015C01
1.198,1.365 2.365,0.354 2.365,0.354 2.708,0.354 false 1.667,1.281 2.365,0.354 false 2.771,0.281 3.083,0.479 0.313,0.198 10 false *a
*a Inspection Point


Check the No. 3 indoor electrical key antenna assembly (inside luggage compartment).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



OK:

Wireless buzzer sounds.




Result:
Proceed to
OK
NG



OK

END (NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)