Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095460 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A2  Open in Front Passenger Side Electrical Antenna Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (for front passenger door) (electrical key antenna) at intervals of 0.25 seconds. For the front door outside handle assembly (for front passenger door) (electrical key antenna) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the front passenger door at intervals of 0.25 seconds. DTC B27A2 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) (electrical key antenna) (between terminals CLG2 and ANT1, or terminals CG2B and ANT2).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A2 Open in Front Passenger Side Electrical Antenna Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) (CLG2 - ANT1, CG2B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Certification ECU (smart key ECU assembly)

·

Front door outside handle assembly (for front passenger door)

·

Wire harness or connector


DTC Output Confirmation Operation:

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for front passenger door -

Related Data List and Active Test Item
DTC Code Data List and Active Test Item
B27A2 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

E270401E58
5.635,0.448 6.104,0.635 0.469,0.188 10 false CLG2 1.208,0.927 1.677,1.115 0.469,0.188 10 false ANT2 0.344,1.469 2.146,1.896 1.802,0.427 10 false H14*1, I13*2 0.354,1.646 2.677,2.052 2.323,0.406 10 false Front Door Outside Handle Assembly (for Front Passenger Door) 1.677,0.365 1.875,0.563 0.198,0.198 10 false 6 5.427,0.354 5.625,0.552 0.198,0.198 10 false 2 5.427,0.802 5.625,1 0.198,0.198 10 false 1 5.635,0.917 6.104,1.104 0.469,0.188 10 false CG2B 1.677,0.813 1.875,1.01 0.198,0.198 10 false 4 5.365,1.26 5.615,1.438 0.25,0.177 10 false 11 5.438,1.979 6.969,2.448 1.531,0.469 10 false Certification ECU (Smart Key ECU Assembly) 1.219,0.438 1.688,0.625 0.469,0.188 10 false ANT1 5.438,1.844 5.906,2.031 0.469,0.188 10 false F13 5.635,1.375 5.885,1.552 0.25,0.177 10 false E 2.948,2.167 4.75,2.594 1.802,0.427 10 false *1: for LHD 2.948,2.448 4.771,2.792 1.823,0.344 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to smart entry and start system (for Entry Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))
a.

Disconnect the F13 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H14*1 or I13*2 front door outside handle assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F13-2 (CLG2) - H14-6 (ANT1) Always Below 1 Ω
F13-1 (CG2B) - H14-4 (ANT2) Always Below 1 Ω
F13-11 (E) - Body ground Always Below 1 Ω
F13-2 (CLG2) or H14-6 (ANT1) - Body ground Always 10 kΩ or higher
F13-1 (CG2B) or H14-4 (ANT2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F13-2 (CLG2) - I13-6 (ANT1) Always Below 1 Ω
F13-1 (CG2B) - I13-4 (ANT2) Always Below 1 Ω
F13-11 (E) - Body ground Always Below 1 Ω
F13-2 (CLG2) or I13-6 (ANT1) - Body ground Always 10 kΩ or higher
F13-1 (CG2B) or I13-4 (ANT2) - Body ground Always 10 kΩ or higher



d.

Reconnect the F13 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))
B343192C22
5.094,0.323 5.51,0.552 0.417,0.229 3.281,0.354 3.698,0.583 0.417,0.229 1.688,0.344 2.104,0.573 0.417,0.229 6.063,1.25 6.719,2.156 true 4.75,2.167 5.917,1.24 true 6.01,1.385 6.021,2.146 true 6,2.188 6.156,2.385 0.156,0.198 10 false E 6.573,2.188 7.094,2.469 0.521,0.281 10 false CG2B 4.563,2.208 5.198,2.448 0.635,0.24 10 false CLG2 5.198,0.354 5.76,0.521 0.563,0.167 10 false F13 1.156,2.708 1.469,2.906 0.313,0.198 10 false *b 4.573,2.729 5.042,2.969 0.469,0.24 10 false *c 4.156,3.688 4.625,3.927 0.469,0.24 10 false GND 0.74,3.688 1.208,3.927 0.469,0.24 10 false GND 0.448,0.167 0.76,0.365 0.313,0.198 10 false *a 3.406,0.385 3.969,0.552 0.563,0.167 10 false F12 1.792,0.375 2.354,0.542 0.563,0.167 10 false F10
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Waveform 2 - -


a.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
F13-2 (CLG2) - F13-11 (E) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 2)
F13-1 (CG2B) - F13-11 (E) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 2)


*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK



Result:
Proceed to
OK
NG



OK

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)
a.

Replace the front door outside handle assembly (for front passenger door) with a new one or the front door outside handle assembly (for driver door) if it is functioning properly.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A2 is not output.



Result:
Proceed to
OK
NG



OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)