Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
67492A
3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH
Disengage the 2 clips and guide and remove the front door lower frame bracket garnish.
69284C
4.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug.
5.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)
Using a moulding remover, disengage the 2 clips, 4 claws and 2 guides.
Disconnect each connector and remove the power window regulator master switch assembly with front door upper armrest base panel.
6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)
Using a moulding remover, disengage the 2 clips, 4 claws and 2 guides.
Disconnect each connector and remove the power window regulator switch assembly with front door upper armrest base panel.
81230N
7.REMOVE COURTESY LIGHT ASSEMBLY
67602
8.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
|
Protective Tape |
Put protective tape around the front door panel.
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw and open the cover.
Remove the 3 screws.
Disengage the 10 clips and remove the front door trim board sub-assembly as shown in the illustration.
w/ Memory:
Disconnect the connector.
w/ Illumination:
Disconnect the connector.
Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.
69206B
9.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
Disengage the 2 claws and guide, and remove the front door inside handle sub-assembly.
68172A
10.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP
Disengage the 7 claws and remove the front door inner glass weatherstrip as shown in the illustration.
84927C
11.REMOVE SEAT MEMORY SWITCH (w/ Memory)
89430
12.REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Memory)
13.REMOVE OUTER REAR VIEW MIRROR WITH COVER
86160
14.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
67832
15.REMOVE FRONT DOOR SERVICE HOLE COVER
Remove the front door service hole cover.
Remove any remaining butyl tape from the front door panel.
68102
16.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Remove the grommet.
Connect the cable to the negative (-) battery terminal.
for Driver Side:
Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the power window regulator master switch assembly.
for Front Passenger Side:
Connect the power window regulator switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the power window regulator switch assembly.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the power window regulator master switch assembly.
Remove the 2 bolts.
After the bolts are removed, do not allow the front door glass sub-assembly to fall.
Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.
Do not damage the front door glass sub-assembly.
17.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY
| *a | Temporary Bolt |
Disconnect the connector.
Loosen the temporary bolt.
Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator assembly may fall and cause damage.
Remove the 5 bolts.
Remove the front door window regulator assembly.
Remove the temporary bolt from the front door window regulator assembly.
85720D
18.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY
Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly.
68151D
19.REMOVE FRONT DOOR GLASS RUN
Remove the front door glass run.
67402F
20.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
Remove the 2 bolts and disconnect wire harness.
Remove the 2 bolts.
Disengage the guide and remove the front door front lower frame sub-assembly.
67404F
21.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
Remove the bolt.
Disengage the guide and remove the front door rear lower frame sub-assembly.
22.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.
The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.
69217D
23.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)
Using a screwdriver, disengage the claw and 2 guides, and remove the front door outside handle cover as shown in the illustration.
69217D
24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.
The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.
69220
25.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY
w/ Smart Entry and Start System:
Disengage the 2 claws.
Using a screwdriver, disconnect the connector.
Remove the front door outside handle assembly as shown in the illustration.
69241H
26.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD
Disengage the 3 claws and remove the front door front outside handle pad.
69242E
27.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD
Disengage the 2 claws and remove the front door rear outside handle pad.
69040A
28.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY
| *1 | Front Door Lock Open Rod |
Disconnect the connector.
Using a T30 "TORX" socket wrench, remove the 3 screws.
Slide the front door lock with motor assembly downward to disconnect the front door lock open rod and remove the front door lock with motor assembly and cables as a unit.
When reusing the front door lock with motor assembly:
Remove the door lock wiring harness seal from the front door lock with motor assembly.
69720B
29.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
Using a screwdriver, disengage the 2 claws as shown in the illustration.
Remove the front door lock remote control cable assembly as shown in the illustration.
69760C
30.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY
Remove the front door inside locking cable assembly as shown in the illustration.
69202A
31.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
w/ Smart Entry and Start System:
Disengage the 3 clamps.
| *A | Inside |
| *B | Outside |
Using a T30 "TORX" socket wrench, loosen the screw.
Slide the front door outside handle frame sub-assembly to disengage the claw, and then remove it.
69312
32.REMOVE FRONT DOOR LOCK OPEN ROD
Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.
68620
33.REMOVE FRONT DOOR CHECK ASSEMBLY
|
Bolt |
|
Nut |
Remove the bolt, 2 nuts and front door check assembly.
67862
34.REMOVE FRONT DOOR WEATHERSTRIP
Using a clip remover, disengage the 20 clips and remove the front door weatherstrip.
67924
35.REMOVE FRONT DOOR NO. 2 STIFFENER CUSHION
|
Double-sided Tape |
Remove the 2 bolts.
Disengage the 2 guides and remove the front door No. 2 stiffener cushion.
67663D
36.REMOVE DOOR FRAME GARNISH
Disengage the 3 claws and remove the door frame garnish.
67001A
37.REMOVE FRONT DOOR PANEL CUSHION
Disengage the 2 claws and remove the 2 front door panel cushions.
67856D
38.REMOVE FRONT DOOR PANEL PROTECTOR
Remove the front door panel protector.
67838A
39.REMOVE FRONT DOOR VENT SEAL
|
Double-sided Tape |
Remove the front door vent seal.
75720
40.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY
75756C
41.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING
75754A
42.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING
75939
43.REMOVE FRONT DOOR UPPER INNER BLACK OUT TAPE
75969
44.REMOVE FRONT DOOR REAR INNER BLACK OUT TAPE
45.REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY
75793
46.REMOVE FRONT DOOR UPPER OUTSIDE MOULDING PAD