Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System)
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095462 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  B2779  Engine Starter Communication Malfunction  


DESCRIPTION

If the remote engine start ECU does not respond to the certification ECU (smart key ECU assembly) or the remote engine start ID is not registered, this DTC is stored.

If communication between the remote engine start ECU and the certification ECU (smart key ECU assembly) is established and the remote engine start is operated, this DTC and the corresponding history DTC will be cleared.

HINT:

Registration status of the remote engine start ECU ID can be checked using the "Wireless C Code" item in the Data List.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2779 Engine Starter Communication Malfunction One of the following conditions is met (1 trip detection logic*):
·

A remote start communication error occurs.

·

Response is not possible.

·

Registration has not been performed.


·

Remote engine start ECU

·

Main body ECU (multiplex network body ECU)

·

Certification ECU (smart key ECU assembly)


DTC output confirmation operation:

A remote start operation is performed.



*: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine does not start with remote start operation Engine cannot be started by remote start operation only

Related Data List and Active Test
DTC No. Data List and Active Test
B2779
·

Wireless Starter Com ID

·

Wireless C Code



CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.

·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.READ VALUE USING GTS (WIRELESS C CODE)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Entry&Start / Data List.


f.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wireless C Code Registration status between remote engine starter ECU and certification ECU (smart key ECU assembly) No Regd or Regd No Regd: ID not registered between remote engine start ECU and certification ECU (smart key ECU assembly)
Regd: ID registered between remote engine start ECU and certification ECU (smart key ECU assembly)
Problems may be caused by the following:
·

DTC B2779 is stored.

·

Remote engine start ECU registration has not been performed.

·

Malfunctions in the certification ECU (smart key ECU assembly) or remote engine start ECU.


Body Electrical > Entry&Start > Data List
Tester Display
Wireless C Code
50003 125 44

Result:
Result Proceed to
"No Regd" is displayed on the GTS A
"Regd" is displayed on the GTS B



A

2.REGISTER REMOTE ENGINE STARTER ID

B

4.REPLACE REMOTE ENGINE STARTER ECU
2.REGISTER REMOTE ENGINE STARTER ID
a.

Register the remote engine starter ID.


Result:
Proceed to
NEXT



NEXT

3.CHECK REMOTE ENGINE STARTER FUNCTION
3.CHECK REMOTE ENGINE STARTER FUNCTION
a.

Check the remote engine starter function.

OK:

Remote engine starter functions operate normally.



Result:
Proceed to
OK
NG



OK

END (REMOTE ENGINE STARTER ID REGISTRATION WAS DEFECTIVE)

NG

4.REPLACE REMOTE ENGINE STARTER ECU
4.REPLACE REMOTE ENGINE STARTER ECU
a.

Temporarily replace the remote engine starter ECU with a new one.

HINT:

Register the remote engine starter ID.



b.

Check the remote engine starter function.

OK:

Remote engine starter functions operate normally.



Result:
Proceed to
OK
NG



OK

END (REMOTE ENGINE STARTER ECU WAS DEFECTIVE)

NG

5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Temporarily replace the main body ECU (multiplex network body ECU) with a new one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



b.

Check the remote engine starter function.

OK:

Remote engine starter functions operate normally.



Result:
Proceed to
OK
NG



OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)